2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

  1. A098365E02
    Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.

  1. Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

    NOTICE:
    Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).

  1. Check that there is no clearance between the gear and camshaft.

  1. Tighten the flange bolt with the camshaft timing gear fixed in place.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.


2. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. A098176E04
    Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.

  1. A098177E03
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098177E06
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 1 bearing cap:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


3. INSTALL NO. 2 CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.

  1. A098178E03
    Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.

    NOTICE:
    Make sure that the paint mark of the chain is aligned with the timing mark as the Type B camshaft sprocket has several other marks.

  1. A361177E01

  1. A086659
    While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.

  1. A098174E05
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098174E07
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 2 bearing cap:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A098173E04
    While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. A052460E06
    Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.

    NOTICE:
    Make sure that the paint mark of the chain is aligned with the timing mark as the Type B camshaft sprocket has several other marks.

  1. A361177E01


4. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and put the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    If the hook releases the plunger while the chain tensioner is being installed, set the hook again.

  1. A112204E02
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E02
    Turn the crankshaft clockwise, then check that the plunger is extended.


5. CHECK VALVE CLEARANCE

  1. A098170E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.19 to 0.29 mm (0.0075 to 0.0114 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.

  1. Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to TDC/compression.

  1. A098171E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.19 to 0.29 mm (0.0075 to 0.0114 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.


6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surfaces.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover within 3 minutes of applying seal packing.
    3. Do not add engine oil for at least 2 hours after installing the cylinder head cover.

  1. A127550E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    Bolt A:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    Bolt B:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Nut:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


7. INSTALL NO. 2 VENTILATION HOSE

8. INSTALL VENTILATION HOSE

9. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


10. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Install the engine cover with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


11. INSTALL FRONT FENDER APRON SEAL RH

12. INSTALL ENGINE UNDER COVER LH

13. INSTALL ENGINE UNDER COVER RH

14. INSTALL FRONT WHEEL RH

15. INSPECT FOR ENGINE OIL LEAKS
← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (from Jun 2006) →