2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1615/14 Front Airbag Sensor LH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.
If the center airbag sensor assembly receives signals from the front airbag sensor LH, it determines whether or not the SRS should be activated.
DTC B1615/14 is recorded when a malfunction is detected in the front airbag sensor LH circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1615/14
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H002750E35

INSPECTION PROCEDURE


1. CHECK DTC

  1. C114796E01
    Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1615/14 is not output.

    HINT:
    Codes other than DTC B1615/14 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

  1. C114801E03
    Using a service wire, connect connectors 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-2 (+SL) - A13-1 (-SL)
    Always
    Below 1 Ω



NG
Go to step 9
OK


5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

  1. C114791E06
    Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-2 (+SL) - A13-1 (-SL)
    Always
    1 MΩ or higher



NG
Go to step 10
OK


6. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

  1. C114791E06
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A13-2 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    A13-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 11
OK


7. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

  1. C114791E06
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A13-1 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 12
OK


8. CHECK FRONT AIRBAG SENSOR LH

  1. C114793E02
    Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1610/13 and B1615/14 are not output.
    A
    DTC B1610/13 is output.
    B
    DTC B1615/14 is output.
    C

    HINT:
    Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



B
REPLACE FRONT AIRBAG SENSOR LH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

9. CHECK INSTRUMENT PANEL WIRE (OPEN)

  1. C123717E01
    Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AE4-3 (+SL) - AE4-4 (-SL)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

10. CHECK INSTRUMENT PANEL WIRE (SHORT)

  1. C123716E02
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AE4-3 (+SL) - AE4-4 (-SL)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

11. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

  1. C123716E02
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    AE4-3 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    AE4-4 (-SL) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

12. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

  1. C123716E02
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AE4-3 (+SL) - Body ground
    Always
    1 MΩ or higher
    AE4-4 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE


← B1610/13 Front Airbag Sensor RH Circuit Malfunction (from Jun 2009)B1615/14 Front Airbag Sensor LH Circuit Malfunction (Oct 2006 – May 2009) →