2006-2011 Camry Aurion · Service Manual TRANSMISSION

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Oct 2006


CHECK SHIFT LOCK OPERATION
  1. Move the shift lever to the P position.

  1. Turn the ignition switch off.

  1. Check that the shift lever cannot be moved to any position other than P.

  1. Turn the ignition switch on (IG), depress the brake pedal and check that the shift lever can be moved to another position.
    If operation cannot be done as specified, inspect the shift lock control ECU assembly.


CHECK SHIFT LOCK RELEASE BUTTON OPERATION
  1. Using a screwdriver, remove the shift lock release cover.

  1. When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position other than P.
    If operation cannot be done as specified, check the shift lever assembly installation condition.


CHECK KEY INTERLOCK OPERATION (w/o Smart Entry and Start System)
  1. Turn the ignition switch to the ON position.

  1. Depress the brake pedal and move the shift lever to any position other than P.

  1. Check that the ignition key cannot be turned to the LOCK position.

  1. Move the shift lever to the P position, turn the ignition key to the LOCK position and check that the ignition key can be removed.
    If operation cannot be done as specified, inspect the shift lock control ECU assembly.


INSPECT SHIFT LOCK CONTROL ECU ASSEMBLY (w/o Smart Entry and Start System)

  1. C127833E09
    Measure the voltage according to the value(s) in the table below.

    HINT:
    Do not disconnect the shift lock control unit assembly connector.


    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    6 (ACC) - 1 (E)
    Ignition switch ON
    10 to 14 V
    6 (ACC) - 1 (E)
    Ignition switch ACC
    10 to 14 V
    6 (ACC) - 1 (E)
    Ignition switch off
    Below 1 V
    4 (STP) - 1 (E)
    Brake pedal depressed
    10 to 14 V
    4 (STP) - 1 (E)
    Brake pedal released
    Below 1 V
    5 (KLS+) - 1 (E)
    1. 1. Ignition switch ACC and shift lever P position
    2. 2. Ignition switch ACC and shift lever except P position
    3. 3. Ignition switch ACC and shift lever P position (After approx. 1 second)
    1. 7.5 to 11 V
    2. Below 1 V
    3. 6 to 9 V
    8 (IG) - 1 (E)
    Ignition switch ON
    10 to 14 V
    8 (IG) - 1 (E)
    Ignition switch off
    Below 1 V

  1. C127833E10
    Measure the resistance according to the value(s) in the table below.

    HINT:
    Do not disconnect the shift lock control ECU assembly connector.


    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, replace the shift lock control ECU assembly.


INSPECT SHIFT LOCK CONTROL ECU ASSEMBLY (w/ Smart Entry and Start System)

  1. C129009E05
    Measure the voltage according to the value(s) in the table below.

    HINT:
    Do not disconnect the shift lock control ECU assembly connector.


    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    12 (IG) - 3 (E)
    Engine switch on (IG)
    10 to 14 V
    12 (IG) - 3 (E)
    Engine switch off
    Below 1 V
    6 (STP) - 3 (E)
    Brake pedal depressed
    10 to 14 V
    6 (STP) - 3 (E)
    Brake pedal released
    Below 1 V

  1. C129009E06
    Measure the resistance according to the value(s) in the table below.

    HINT:
    Do not disconnect the shift lock control ECU assembly connector.


    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    3 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, replace the shift lock control ECU assembly.

← INSTALLATION (from Jun 2009)COMPONENTS (from Oct 2006) →