2006-2011 Camry Aurion · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2006


1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C135707
    Remove the nut, washer, and control shaft lever.

  1. C135708
    Using a screwdriver, unstake the lock plate, and remove the lock nut and lock plate.

  1. C135710
    Remove the 2 bolts and pull out the park/neutral position switch.


2. REMOVE NO. 2 BREATHER PLUG

  1. C134833
    Remove the No. 2 breather plug from the transaxle case.

  1. C134834E01
    Remove the hose and O-ring from the No. 2 breather plug.


3. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

  1. C083143E03
    Remove the union.

  1. Remove the O-ring from the union.


4. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

  1. C083144E04
    Remove the union.

  1. Remove the O-ring from the union.


5. REMOVE SPEED SENSOR

  1. D030672E04
    Remove the 2 bolts and the 2 speed sensors from the transaxle assembly.


6. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C134835
    Remove the 4 No. 1 transaxle case plugs from the transaxle case.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.


7. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

  1. C134836
    Support the transaxle assembly.


8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and drain plug gasket from the oil pan.

  1. C091925
    Remove the 18 bolts, oil pan, and gasket.

  1. C134837E01
    Remove the 2 transmission oil cleaner magnets from the oil pan.


9. INSPECT TRANSMISSION OIL CLEANER MAGNET

  1. AT00103E03
    Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.

    Result:
    Steel (magnetic):
    bearing, gear, and plate wear
    Brass (non-magnetic):
    bushing wear


10. DISCONNECT TRANSMISSION WIRE

  1. C134838E01
    Disconnect the 7 connectors from the shift solenoid valves.

  1. Remove the bolt, lock plate, and ATF temperature sensor.


11. REMOVE TRANSMISSION WIRE

  1. D003547E05
    Remove the bolt and transmission wire from the transaxle case.


12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. C134839
    Remove the 3 bolts and oil strainer.

  1. C091932E02
    Remove the O-ring from the oil strainer.


13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. C091933
    Support the valve body assembly and remove the 17 bolts and valve body assembly.


14. REMOVE NO. 1 GOVERNOR APPLY GASKET

  1. C083127
    Remove the No. 1 governor apply gasket from the transaxle case.


15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

  1. C083128
    Remove the transaxle case 2nd brake gasket from the transaxle case.


16. REMOVE BRAKE DRUM GASKET

  1. C083129
    Remove the brake drum gasket from the transaxle case.


17. REMOVE CHECK BALL BODY

  1. D003554E01
    Remove the check ball body and spring from the transaxle case.


18. REMOVE C-3 ACCUMULATOR PISTON

  1. D003555
    Remove the spring from the C-3 accumulator piston.

  1. C134840
    Using needle-nose pliers, remove the C-3 accumulator piston from the transaxle case.

  1. C134841E01
    Remove the O-ring from the C-3 accumulator piston.


19. REMOVE REVERSE CLUTCH ACCUMULATOR PISTON

  1. D026401
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the reverse accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
    2. Take care not to splash ATF when applying the air.

  1. D026402E07
    Remove the 2 O-rings from the reverse clutch accumulator piston.


20. REMOVE B-3 ACCUMULATOR PISTON

  1. D003558E01
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
    2. Take care not to splash ATF when applying the air.

  1. D003904E06
    Remove the O-ring from the B-3 accumulator piston.


21. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING

  1. D003559
    Using needle-nose pliers, remove the manual valve lever shaft retainer spring.


22. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

  1. D003560
    Remove the 2 bolts and manual detent spring sub-assembly.


23. REMOVE PARKING LOCK PAWL BRACKET

  1. C056727
    Remove the 2 bolts and parking lock pawl bracket.


24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

  1. C134842E01
    Using a screwdriver, slide the spacer.

  1. C134843
    Using a pin punch (φ3 mm) and hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle case.

  1. C134844
    Remove the manual valve lever shaft, manual valve lever, and spacer.


25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. C134845E01
    Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.

    HINT:
    Align the dial with the notches on the manual valve lever sub-assembly to remove the parking lock rod sub-assembly.


26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. D003566
    Using a screwdriver, remove the oil seal from the transaxle case.


27. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY
  1. Support the transaxle case with the oil pump side facing up.


28. INSPECT INPUT SHAFT END PLAY

  1. D008091
    Using a dial indicator, measure the input shaft end play.

    End play:
    0.262 to 1.244 mm (0.01 to 0.049 in.)


29. REMOVE TRANSAXLE HOUSING

  1. C147840
    Remove the 18 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed when the transaxle housing is removed.


30. REMOVE OIL PUMP ASSEMBLY

  1. D003569E03
    Remove the 7 bolts and oil pump from the transaxle case.


31. REMOVE THRUST NEEDLE ROLLER BEARING

  1. D025505E06
    Remove the thrust needle roller bearing from the underdrive planetary gear assembly.


32. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE

  1. D025506E05
    Remove the No. 2 thrust bearing underdrive race from the underdrive planetary gear assembly.


33. REMOVE DIFFERENTIAL GEAR ASSEMBLY

  1. D026450E07
    Remove the differential gear assembly from the transaxle case.


34. REMOVE OVERDRIVE BRAKE GASKET

  1. D003573
    Remove the 2 overdrive brake gaskets from the transaxle case.


35. REMOVE FORWARD CLUTCH ASSEMBLY

  1. D003574E04
    Remove the forward clutch assembly from the transaxle case.

  1. D003906E03
    Remove the thrust needle roller bearing from the forward clutch.


36. REMOVE MULTIPLE DISC CLUTCH HUB

  1. D026787E05
    Remove the thrust needle roller bearing, multiple disc clutch hub, thrust needle roller bearing and No. 1 thrust bearing race from the transaxle case.


37. INSPECT MULTIPLE DISC CLUTCH HUB

  1. D003829E06
    Using a dial indicator, measure the inside diameter of the multiple disc clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    If the diameter is greater than the maximum, replace the multiple disc clutch hub with a new one.

    NOTICE:
    Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discoloration is identified, replace the direct clutch sub-assembly with a new one.


38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. D003576E04
    Remove the bolt and pawl shaft clamp from the transaxle case.

  1. D009652
    Remove the parking lock pawl shaft from the transaxle case.

  1. D009689
    Push the parking lock pawl.

    HINT:
    Failure to do so will cause interference when the underdrive planetary gear is removed.

  1. D003579E05
    Remove the underdrive planetary gear assembly from the transaxle case.

    NOTICE:
    Do not drop the underdrive planetary gear assembly.


39. REMOVE PARKING LOCK PAWL

  1. D026386
    Remove the spring, pawl pin and parking lock pawl.


40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY

  1. D003580E03
    Remove the underdrive clutch assembly, thrust bearing, and bearing race from the transaxle case.


41. REMOVE UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003581E03
    Using a screwdriver, remove the snap ring from the transaxle case.

  1. C134846E01
    Remove the underdrive one-way clutch from the transaxle case.

  1. D003907E01
    Remove the outer race retainer from the one-way clutch.


42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC

  1. D026466E01
    Using a screwdriver, remove the snap ring.

  1. C134847E01
    Remove the flange, 3 discs and 3 plates from the transaxle case.


43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC

  1. D009196
    Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


44. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY

  1. C134848
    Remove the 11 bolts.

  1. Tap on the circumference of the rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.


45. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C134849
    Remove the 4 No. 1 transaxle case plugs from the transaxle rear cover.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.


46. REMOVE REAR CLUTCH OIL SEAL RING

  1. D026389E02
    Remove the 3 rear clutch oil seal rings from the transaxle rear cover.


47. REMOVE NEEDLE ROLLER BEARING

  1. D026472E01
    Using SST, remove the needle roller bearing from the transaxle rear cover.
    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)


48. REMOVE NO. 1 GOVERNOR APPLY GASKET

  1. D026390
    Using a screwdriver, remove the 3 apply gaskets.


49. REMOVE BRAKE APPLY TUBE

  1. C134851E01
    Remove the bolt, clamp and brake apply tube.

  1. Remove the clutch apply tube.

  1. Remove the brake apply tube from the clamp.


50. REMOVE DIRECT CLUTCH ASSEMBLY

  1. D026403E04
    Remove the thrust bearing and the direct clutch assembly from the transaxle case.


51. INSPECT PACK CLEARANCE OF DIRECT CLUTCH

  1. C134884
    Install the intermediate shaft and needle roller bearing on the transaxle rear cover.

    NOTICE:
    Be careful not to damage the oil seal ring outers.

  1. Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    0.60 to 0.82 mm (0.02362 to 0.03228 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.


52. INSPECT PACK CLEARANCE OF OVERDRIVE CLUTCH

  1. C134885
    Using a dial indicator, measure the overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    0.52 to 0.83 mm (0.02047 to 0.03268 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.


53. REMOVE DIRECT MULTIPLE DISC CLUTCH DISC

  1. D026419E01
    Using a screwdriver, remove the snap ring from the intermediate shaft.

  1. D026420
    Remove the flange, 3 discs, 3 plates and cushion plate from the intermediate shaft.


54. INSPECT DIRECT MULTIPLE DISC CLUTCH DISC

  1. C134886
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


55. REMOVE OVERDRIVE DIRECT CLUTCH DISC

  1. C134887
    Using a screwdriver, remove the snap ring from the intermediate shaft.

  1. Remove the flange, 3 discs and 3 plates from the intermediate shaft.


56. INSPECT OVERDRIVE DIRECT CLUTCH DISC

  1. D026719
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


57. REMOVE OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D003677E01
    Place SST on the clutch balancer and compress the spring with a press.
    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring from the direct clutch drum.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. D026424E02
    Remove the clutch balancer from the overdrive direct clutch drum.

  1. D026423E05
    Remove the overdrive clutch return spring from the overdrive direct clutch drum.


58. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D009211E02
    Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    25.91 mm (1.0201 in.)

    If the free length is shorter than the standard free length, replace the overdrive clutch return spring sub-assembly.


59. REMOVE OVERDRIVE DIRECT CLUTCH PISTON

  1. D026463
    Install the intermediate shaft on the transaxle rear cover.

  1. Holding the direct clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the direct clutch piston.


60. REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. D026425
    Holding the direct clutch drum by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the direct clutch drum.


61. REMOVE OVERDRIVE DIRECT CLUTCH O-RING

  1. D026464E01
    Using a screwdriver, remove the O-ring from the direct clutch drum.


62. REMOVE OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY

  1. D026392E05
    Remove the thrust bearing race, thrust bearing, and overdrive direct clutch hub from the planetary gear assembly.


63. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

  1. D026714E04
    Remove the rear planetary sun gear assembly from the transaxle case.

  1. C134852
    Remove the thrust needle roller bearing and thrust bearing race from the rear planetary sun gear assembly.

  1. D026393E02
    Remove the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.


64. REMOVE ONE-WAY CLUTCH ASSEMBLY

  1. D026598E04
    Remove the one-way clutch assembly and the thrust needle roller bearing from the transaxle case.

  1. D003909E05
    Remove the one-way clutch inner race from the one-way clutch assembly.


65. REMOVE ONE-WAY CLUTCH SLEEVE

  1. D003589E06
    Remove the one-way clutch sleeve from the transaxle case.


66. REMOVE NO. 1 PLANETARY CARRIER THRUST WASHER

  1. C134853E01
    Remove the No. 1 planetary carrier thrust washer from the planetary gear assembly.


67. REMOVE 2ND BRAKE DISC

  1. C134854E01
    Using a screwdriver, remove the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transaxle case.


68. INSPECT 2ND BRAKE DISC

  1. D026717
    Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


69. REMOVE SECOND BRAKE PISTON ASSEMBLY

  1. D008058E04
    Using a screwdriver, remove the snap ring.

  1. D026396E05
    Remove the second brake piston assembly from the transaxle case.


70. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. D026703E01
    Place SST on the return spring and compress it with a press.
    SST
    09387-00060  

  1. Using a screwdriver, remove the snap ring.

  1. D026704E03
    Remove the 2nd brake piston return spring sub-assembly.


71. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C089124E02
    Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    16.61 mm (0.6539 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


72. REMOVE 2ND BRAKE PISTON

  1. D026705
    Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.


73. REMOVE 2ND BRAKE PISTON O-RING

  1. D026706E04
    Remove the 2 O-rings from the 2nd brake piston.


74. REMOVE REAR PLANETARY GEAR ASSEMBLY

  1. D003616E01
    Using a screwdriver, remove the snap ring.

  1. D026591E03
    Remove the rear planetary gear assembly from the transaxle case.


75. REMOVE INPUT SUN GEAR

  1. C134855E01
    Remove the 2 thrust needle roller bearings, No. 2 thrust bearing races, No. 3 thrust bearing race, and input sun gear from the transaxle case.


76. REMOVE 1ST AND REVERSE BRAKE DISC

  1. C134856
    Remove the flange, 5 discs and 5 plates from the transaxle case.


77. INSPECT 1ST AND REVERSE BRAKE DISC

  1. D009189
    Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


78. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. D003595E03
    Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut, and the nut cannot be loosened.

  1. D003596E01
    Using SST, remove the nut and washer.
    SST
    09387-00030  
    09387-00080  

  1. D026398E01
    Using SST and a press, remove the front planetary gear assembly from the counter drive gear.
    SST
    09950-60010   (09951-00450)
    09950-70010   (09951-07100)

  1. D026763E02
    Remove the front planetary gear assembly from the brake hub.


79. REMOVE FRONT PLANETARY RING GEAR

  1. D003615E04
    Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.


80. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D003600E01
    Place SST on the return spring, and compress the return spring with a press.
    SST
    09387-00070  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. Remove the return spring.


81. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. C141534
    Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.63 mm (0.6941 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


82. REMOVE 1ST AND REVERSE BRAKE PISTON

  1. D026405E06
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
    2. Take care not to splash ATF when applying the air.

  1. D026713E02
    Remove the 2 O-rings from the 1st and reverse brake piston.


83. REMOVE COUNTER DRIVE GEAR

  1. C134861E01
    Using SST and a press, remove the counter drive gear from the transaxle case.
    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)

  1. D003602E01
    Tighten the 2 bolts evenly and make a clearance of approx. 20.0 mm (0.797 in.) between the counter drive gear and the inner race.

  1. C134858E01
    Using SST, remove the tapered roller bearing inner race.
    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00590)


84. REMOVE COUNTER DRIVE ANGULAR BALL BEARING

  1. C134859E01
    Remove the bearing inner race (rear side) and angular ball (rear side).

  1. C134860E01
    Using SST, remove the bearing outer race (rear side) from the transaxle case.
    SST
    09308-00010  

  1. C134925
    Remove the angular ball (front side).

  1. C134862E01
    Using SST and a press, remove the bearing outer race (front side) from the transaxle case.
    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07200)

  1. C134863
    Using a screwdriver, remove the snap ring from the transaxle case.


85. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D026407E01
    Place SST on the return spring, and compress the return spring with a press.
    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. Remove the return spring.


86. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. C141534
    Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    13.24 mm (0.5213 in.)

    If the free length is shorter than the standard free length, replace the underdrive brake return spring sub-assembly.


87. REMOVE UNDERDRIVE BRAKE PISTON

  1. D026406E02
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.

  1. D003794E03
    Remove the 2 O-rings from the underdrive brake piston.


88. REMOVE NEEDLE ROLLER BEARING

  1. D003605E03
    Using SST, remove the needle roller bearing from the transaxle case.
    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)


89. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING

  1. D003914E05
    Remove the 2 oil seal rings from the transaxle case.


90. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. D026383
    Remove the 2 No. 1 transaxle case plugs.

  1. Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.


91. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING

  1. C134864E01
    Using SST, remove the underdrive cylindrical roller bearing from the transaxle case.
    SST
    09820-00031  
    09950-40011   (09952-04010, 09954-04010, 09955-04061, 09957-04010)
    09950-50013   (09951-05010, 09953-05020)


92. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING

  1. D003915E08
    Remove the oil seal ring from the transaxle housing.


93. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. C134866E01
    Remove the bolt, transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.

← COMPONENTS (from Jun 2006)INSPECTION (from Jun 2006) →