2006-2011 Camry Aurion · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Jun 2006


1. BEARING POSITION

  1. Check the bearing position.

    C110530E01

    Mark
    Front Race Diameter
    Inside / Outside (mm (in.))
    Thrust Bearing Diameter
    Inside / Outside (mm (in.))
    Rear Race Diameter
    Inside / Outside (mm (in.))
    A
    -
    53.0 (2.087) / 78.2 (3.079)
    52.1 (2.051) / 75.5 (2.972)
    B
    -
    37.73 (1.4854) / 58.0 (2.284)
    29.9 (1.177) / 55.5 (2.185)
    C
    -
    33.85 (1.3327) / 52.2 (2.055)
    -
    D
    -
    23.5 (0.925) / 44.0 (1.732)
    -
    E
    -
    36.3 (1.429) / 52.2 (2.055)
    34.5 (1.358) / 48.5 (1.909)
    F
    34.5 (1.358) / 56.82 (2.2370)
    32.4 (1.276) / 56.62 (2.2291)
    -
    G
    40.3 (1.587) / 58.0 (2.284)
    38.6 (1.520) / 60.0 (2.362)
    38.6 (1.520) / 58.0 (2.284)
    H
    -
    53.6 (2.110) / 69.6 (2.740)
    -
    I
    33.1 (1.303) / 45.4 (1.787)
    31.85 (1.2539) / 45.2 (1.780)
    -
    J
    -
    25.0 (0.984) / 39.5 (1.555)
    23.6 (0.929) / 36.6 (1.441)
    K
    -
    55.9 (2.201) / 76.0 (2.992) or 76.6 (3.016)
    -


2. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. C134866E01
    Install the differential gear lube apply tube and transaxle apply tube clamp to the transaxle housing with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    Make sure to insert the pipe to the stopper.


3. INSTALL NO. 1 TRANSAXLE CASE PLUG

  1. D026383
    Install 2 new O-rings to the 2 No. 1 transaxle case plugs.

  1. Install the 2 No. 1 transaxle case plugs to the transaxle rear housing.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


4. INSTALL UNDERDRIVE OUTPUT SHAFT OIL SEAL RING

  1. D003915E08
    Coat a new oil seal ring with ATF and install it to the transaxle housing.


5. INSTALL UNDERDRIVE CYLINDRICAL ROLLER BEARING

  1. D003807E01
    Coat the underdrive cylindrical roller bearing with ATF.

  1. Using SST and a press, install the underdrive cylindrical roller bearing.

    SST
    09950-60020  
    09950-70010   (09951-00780, 09951-07100)

    NOTICE:
    Do not apply excessive pressure to it.


6. INSTALL UNDERDRIVE CLUTCH DRUM OIL SEAL RING

  1. D003914E05
    Coat 2 new oil seal rings with ATF, and install them to the transaxle rear cover.

    NOTICE:
    1. Do not expand the gap of the oil seal ring excessively.
    2. Securely engage the hooks. Confirm the smooth rotation.


7. INSTALL NEEDLE ROLLER BEARING

  1. D003809E08
    Wind vinyl tape around SST at the place 4.0 mm (0.157 in.) above the bottom end until the thickness of the wound tape is about 5.0 mm (0.197 in.).

    NOTICE:
    Clean SST to remove deposited oil before winding vinyl tape.

  1. Coat a new needle roller bearing with ATF.

  1. D003810E01
    Using SST and a press, install the needle roller bearing to the transaxle case.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    When the wound vinyl tape contacts the transaxle case, stop press-fitting.


8. INSTALL UNDERDRIVE BRAKE PISTON

  1. D003794E03
    Coat 2 new O-rings with ATF, and install them to the underdrive brake piston.

    NOTICE:
    1. Ensure the O-rings are not pinched or twisted.
    2. Apply enough ATF to the O-rings prior to installation.

  1. Coat the underdrive brake piston with ATF.

  1. D026764E01
    Install the underdrive brake piston to the transaxle case.

    NOTICE:
    Be careful not to damage the O-rings.


9. INSTALL UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D026407E01
    Place SST on the return spring and compress the return spring with a press.
    SST
    09387-00020  

  1. Using a snap ring expander, install the snap ring to the transaxle case.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.
    3. After installing the spring sub-assembly, check all of the springs are fitted in the piston correctly.
    4. The snap ring should be securely engaged in the groove of the transaxle case.


10. INSTALL COUNTER DRIVE ANGULAR BALL BEARING

  1. C134867
    Install the snap ring to the transaxle case.

  1. C134868E01
    Using SST and a press, install the bearing outer race (rear side) to the transaxle case.
    SST
    09316-12010  
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)

    NOTICE:
    1. Ensure that the snap ring is securely installed.
    2. Do not apply excessive pressure to the bearing outer race.

  1. C134869E01
    Using SST and a press, install the bearing outer race (front side) to the transaxle case.
    SST
    09316-12010  
    09502-24010  
    09523-36010  
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)

    NOTICE:
    1. Do not apply excessive pressure to the bearing outer race.
    1. Install the bearing outer race with a press while holding the bearing outer race with SST (09502-24010, 09523-36010).

  1. Install the 2 angular balls to the transaxle case.


11. INSTALL COUNTER DRIVE GEAR
  1. Coat the counter drive gear with ATF.

  1. C134870E01
    Using SST and a press, install the tapered roller bearing inner race (front side) to the counter drive gear.
    SST
    09649-17010  
    09950-70010   (09951-07150)

    NOTICE:
    Do not apply excessive pressure to the bearing inner race.

  1. C134871E01
    Using SST and a press, install the counter drive gear and bearing inner race (rear side) to the transaxle case.
    SST
    09223-15030  
    09527-17011  
    09950-60020   (09951-00720)
    09950-70010   (09951-07150)

    NOTICE:
    Do not apply excessive pressure to the counter drive gear and bearing inner race.


12. INSTALL 1ST AND REVERSE BRAKE PISTON

  1. D026713E02
    Coat 2 new O-rings with ATF.

  1. Install the 2 O-rings to the 1st and reverse brake piston.

    NOTICE:
    1. Ensure the O-rings are not pinched or twisted.
    2. Apply enough ATF to the O-rings prior to installation.

  1. D026593E02
    Coat the 1st and reverse brake piston with ATF, and install it to the transaxle case.

    NOTICE:
    Be careful not to damage the O-rings.


13. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
  1. Install the return spring.

  1. D003600E01
    Place SST on the return spring and compress the return spring with a press.
    SST
    09387-00070  

  1. Using a snap ring expander, install the snap ring to the transaxle case.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.
    3. After installing the spring sub-assembly, check all of the springs are fitted in the piston correctly.
    4. The snap ring should be securely engaged in the groove of the cylinder.


14. INSTALL FRONT PLANETARY RING GEAR

  1. D003615E04
    Using a screwdriver, install the front planetary ring gear and snap ring to the brake hub.

    NOTICE:
    Confirm that the snap ring is engaged in the groove of the brake hub correctly.


15. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. D026763E02
    Install the front planetary gear assembly to the brake hub.

  1. C134872E01
    Using SST and a press, press-fit the front planetary gear assembly.
    SST
    09950-60010   (09951-00500)
    09950-70010   (09951-07100)

    NOTICE:
    1. Do not apply excessive pressure to the front planetary gear assembly.
    2. Press the inner race of the LH tapered roller bearing, counter gear, and front planetary gear assembly to the position where no pre-load is applied to one pair of tapered roller bearings (left and right).

  1. D003917E02
    Install a new washer as shown in the illustration.

  1. D003596E01
    Using SST, install the nut.
    SST
    09387-00030  
    09387-00080  

    Torque:
    185 N*m{ 1,886 kgf*cm , 136 ft.*lbf }

  1. D003918E01
    Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm. If the measured value is not within the specified range, gradually tighten the nut until the turning torque falls within the specified range.
    SST
    09387-00080  

    Torque:
    350 N*m{ 3,569 kgf*cm , 258 ft.*lbf } (a limit)

    Bearing Turning Torque:
    0.19 to 0.4 N*m (1.9 to 4.1 kgf*cm, 1.7 to 3.5 in.*lbf)

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.3 in.) to measure the turning torque.

  1. C134873
    Using a chisel and hammer, stake the front lock washer.


16. INSTALL INPUT SUN GEAR

  1. C134855E02
    Coat the 2 thrust bearings with ATF.

  1. Install the input sun gear, 2 thrust needle roller bearings, 2 No. 2 thrust bearing races, and No. 3 thrust bearings to the transaxle case.

    NOTICE:
    1. Ensure that the parts are installed in the correct order and direction.

    Thrust bearing and bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing Race, A
    34.5 (1.358)
    56.82 (2.2370)
    Thrust Bearing, B
    32.4 (1.276)
    56.62 (2.2291)
    Bearing Race, C
    40.3 (1.587)
    58.0 (2.284)
    Thrust Bearing, D
    38.6 (1.520)
    60.0 (2.362)
    Bearing Race, E
    38.6 (1.520)
    58.0 (2.284)


17. INSTALL REAR PLANETARY GEAR ASSEMBLY

  1. D026591E03
    Install the rear planetary gear assembly to the brake hub.

  1. D003616E01
    Using a screwdriver, install the snap ring.

    NOTICE:
    Confirm that the snap ring is engaged in the groove of the 1st and reverse brake hub correctly.


18. INSTALL 1ST AND REVERSE BRAKE DISC

  1. C134875E01
    Coat the 5 discs with ATF.

  1. Install the 5 plates and 5 discs.

    NOTICE:
    Be careful about the order of discs and plates.


19. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

  1. C134874E01
    Using vernier calipers, measure the distance between the disc surface and the contact surface of the 2nd brake cylinder and transaxle case (Dimension A).

  1. Select an appropriate flange so that the pack clearance will be within the specified range.

    Pack clearance:
    0.745 to 1.21 mm (0.0293 to 0.0476 in.)

    HINT:
    Piston stroke = Dimension A - Flange thickness

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    1.8 (0.071)
    5
    2.2 (0.087)
    2
    1.9 (0.075)
    6
    2.3 (0.091)
    3
    2.0 (0.079)
    7
    2.4 (0.094)
    4
    2.1 (0.083)
    8
    2.5 (0.098)

  1. Install the flange.


20. INSTALL 2ND BRAKE PISTON

  1. D026775
    Coat the 2nd brake piston with ATF, and install it to the 2nd brake cylinder.


21. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. D026704E03
    Install the 2nd brake piston return spring sub-assembly.

    NOTICE:
    Ensure that all springs are fitted in the piston correctly.

  1. D026703E01
    Place SST on the piston return spring, and compress it with a press.
    SST
    09387-00060  

  1. Using a screwdriver, install the snap ring.

    NOTICE:
    Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.


22. INSTALL SECOND BRAKE PISTON ASSEMBLY

  1. D026396E05
    Install the second brake piston assembly to the transaxle case.

  1. D008058E04
    Install the snap ring and measure the inside diameter.

    Inside diameter:
    More than 167 mm (6.57 in.)

    NOTICE:
    1. Make sure to install the tapered snap ring in the correct direction.
    2. When the diameter does not meet the specified value, replace the snap ring with a new one.
    3. After installing the snap ring, confirm that there is no clearance between the second brake cylinder and the fitting surface of the cylinder in the transaxle case.


23. INSTALL ONE-WAY CLUTCH SLEEVE

  1. C092977E02
    Install the one-way clutch sleeve to the 2nd brake cylinder assembly.

    NOTICE:
    Check the positioning direction of the outer sleeve.


24. INSTALL NO. 1 PLANETARY CARRIER THRUST WASHER

  1. D026394E04
    Coat the No. 1 planetary carrier thrust washer with ATF, and install it onto the planetary sun gear assembly.

    NOTICE:
    After installing the washer, confirm that the projections on the washer are securely fitted in the holes of the planetary sun gear assembly.


25. INSTALL ONE-WAY CLUTCH ASSEMBLY

  1. D003909E05
    Install the one-way clutch inner race to the one-way clutch.

    NOTICE:
    1. Check the direction of the inner race.
    2. Confirm that the discrimination mark can be seen.

  1. C134926E01
    Check the rotating direction of the one-way clutch inner race for the lock or free operation, as shown in the illustration.

  1. D026598E04
    Install the one-way clutch and thrust needle roller bearing to the one-way clutch sleeve outer.
    Bearing diameter: mm (in.) 

    Inside
    Outside
    Bearing
    53.6 (2.110)
    69.4 (2.732)

    NOTICE:
    Install the thrust bearing properly so that non-colored race will be visible.


26. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

  1. D026393E02
    Coat the No. 2 planetary carrier thrust washer with ATF, and install it onto the rear planetary sun gear.

  1. D026404E06
    Coat the bearing with ATF, and install it onto the rear planetary sun gear.
    Bearing diameter: mm (in.) 

    Inside
    Outside
    Race, A
    33.1 (1.303)
    45.4 (1.787)
    Bearing, B
    31.85 (1.254)
    45.2 (1.78)

  1. D026714E04
    Install the rear planetary sun gear assembly to the rear planetary gear.

    NOTICE:
    After installing the rear planetary sun gear assembly, confirm that the discs engage.


27. INSTALL 2ND BRAKE DISC

  1. C134876E01
    Coat the 3 discs with ATF.

  1. Install the 3 discs and 3 plates to the transaxle case.

  1. Install the snap ring.


28. INSPECT PACK CLEARANCE OF SECOND BRAKE

  1. C134877E01
    Using vernier calipers, measure the distance between the disc surface and snap ring surface (Dimension B).

  1. Select an appropriate flange so that the pack clearance will be within the specified range.

    Pack clearance:
    0.53 to 0.91 mm (0.0209 to 0.0358 in.)

    HINT:
    Piston stroke = Dimension B - Flange thickness - Snap ring thickness 1.6 mm (0.063 in.)

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    0
    2.9 (0.114)
    5
    3.4 (0.134)
    1
    3.0 (0.118)
    6
    3.5 (0.138)
    2
    3.1 (0.122)
    7
    3.6 (0.142)
    3
    3.2 (0.126)
    8
    3.7 (0.146)
    4
    3.3 (0.130)
    -
    -

  1. Install the flange.


29. INSTALL OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY

  1. D026392E06
    Install the direct clutch hub to the planetary gear assembly.

    NOTICE:
    Be careful not to damage the bushing inside the overdrive clutch hub during installation.

  1. Coat the thrust bearing with ATF.

  1. Install the bearing race and the thrust bearing to the direct clutch hub.

    NOTICE:
    When installing the bearing, hold the side of the overdrive clutch hub.

    Bearing and race diameter: mm (in.) 

    Inside
    Outside
    Bearing, A
    25.0 (0.984)
    39.5 (1.555)
    Race, B
    23.6 (0.929)
    36.6 (1.441)


30. INSTALL OVERDRIVE DIRECT CLUTCH O-RING

  1. D026464E01
    Coat a new O-ring with ATF, and install it to the direct clutch drum.

    NOTICE:
    Ensure that the O-ring is not twisted or pinched.


31. INSTALL OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. D026462E03
    Coat the direct clutch drum with ATF, and install it to the intermediate shaft.

    NOTICE:
    1. Be careful not to damage the O-ring.
    2. Be careful not to damage the lip seal of the direct clutch drum.


32. INSTALL OVERDRIVE DIRECT CLUTCH PISTON

  1. D026461E01
    Coat the overdrive direct clutch piston with ATF, and install it to the overdrive direct clutch drum sub-assembly.

    NOTICE:
    Be careful not to damage the lip seal of the direct clutch piston.


33. INSTALL OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D026423E05
    Install the overdrive clutch return spring sub-assembly to the overdrive direct clutch drum sub-assembly.

    NOTICE:
    When installing the spring sub-assembly, ensure that all springs are fitted in the piston correctly.

  1. Coat the clutch balancer with ATF.

  1. D026424E03
    Install the clutch balancer to the overdrive direct clutch drum sub-assembly.

    NOTICE:
    1. Be careful not to damage the lip seal of the direct clutch balancer.
    2. Ensure that the clutch balancer is not pinched and there are no other defects at the sealing lip.
    3. Apply enough ATF to the sealing lip prior to installation.

  1. D003677E01
    Place SST on the clutch balancer and compress the piston return spring with a press.
    SST
    09387-00020  

  1. Using a snap ring expander, install the snap ring to the direct clutch drum.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. D025588E03
    Position the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Ensure that the end gap of the snap ring is not aligned with any of the stoppers.


34. INSTALL DIRECT MULTIPLE DISC CLUTCH DISC

  1. C134928E01
    Coat the 3 discs with ATF.

  1. Install the 3 plates, 3 discs and flange to the intermediate shaft.

    NOTICE:
    Be careful about the order of the discs, plates and flange.

  1. D026421E02
    Using a screwdriver, install the snap ring.

    NOTICE:
    The snap ring should be securely engaged in the groove of the drum.


35. INSTALL DIRECT MULTIPLE DISC CLUTCH DISC

  1. D026416E01
    Coat the 3 discs with ATF.

  1. Install the cushion plate, 3 plates, 3 discs and flange to the intermediate shaft.

    NOTICE:
    1. Install the cushion plate with the mark on the white surface facing the plate.
    2. Be careful about the order of discs, plates and flange.

  1. D026419E04
    Using a screwdriver, install the snap ring.

    NOTICE:
    The snap ring should be securely engaged in the groove of the drum.


36. INSPECT PACK CLEARANCE OF DIRECT CLUTCH

  1. C134884
    Install the intermediate shaft and needle roller bearing on the transaxle rear cover.

    NOTICE:
    Be careful not to damage the oil seal ring outers.

  1. Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    0.60 to 0.82 mm (0.02362 to 0.03228 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.


37. INSPECT PACK CLEARANCE OF OVERDRIVE CLUTCH

  1. C134885
    Using a dial indicator, measure the overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    0.52 to 0.83 mm (0.02047 to 0.03268 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.


38. INSTALL DIRECT CLUTCH ASSEMBLY

  1. D026403E04
    Coat the thrust bearing with ATF.

  1. Install the direct clutch assembly and thrust bearing to the rear planetary sun gear assembly.

    NOTICE:
    The disc in the direct clutch should completely match with the hub attached outside the rear planetary sun gear. Otherwise, the rear cover cannot be installed.

  1. C134878E01
    Clean the contact surfaces of the transaxle case and the rear cover.

  1. As shown in the illustration, place a straight edge on the direct clutch drum and measure the distance between the transaxle case and the straight edge using vernier calipers (Dimension C).

  1. D026470E02
    Using vernier calipers and a simple straight edge, measure the dimension shown in the illustration.

  1. Calculate the end play value using the formula below. Select a thrust bearing which satisfies the specified end play value and install it.

    End play:
    0.199 to 0.970 mm (0.0078 to 0.0382 in.)

    NOTICE:
    Make sure that the non-colored race side is facing the direct clutch assembly.

    HINT:
    End play = Dimension D - Dimension C

    Bearing thickness and diameter: mm (in.) 
    Thickness
    Inside
    Outside
    3.6 (0.1417)
    55.9 (2.201)
    76.0 (2.992)
    3.8 (0.150)
    55.9 (2.201)
    76.6 (3.016)


39. INSTALL NO. 1 GOVERNOR APPLY GASKET

  1. D026390
    Install 3 new No. 1 governor apply gaskets to the transaxle case.


40. INSTALL BRAKE APPLY TUBE

  1. D003923
    Install the clamp to the brake apply tube.

    NOTICE:
    Make sure to install the clamp to the apply tube before installing the apply tube to the transaxle case. This prevents the apply tube from being deformed or damaged.

  1. Install the clutch apply tube.

  1. C134851E01
    Install the brake apply tube to the transaxle case with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Each pipe should be securely inserted until it reaches the stopper.


41. INSTALL NEEDLE ROLLER BEARING

  1. D026766E01
    Using SST and a press, install the needle roller bearing to the transaxle rear cover.
    SST
    09950-60010   (09951-00230, 09952-06010, 09951-00360)

    Press fit depth:
    20.55 to 21.25 mm (0.8091 to 0.8366 in.)

    NOTICE:
    1. Face the inscribed mark side of the bearing race up.
    2. Keep pressing until the specified value is obtained.

  1. Coat the needle roller bearing with ATF.


42. INSTALL REAR CLUTCH OIL SEAL RING

  1. D026389E02
    Coat 3 new rear clutch oil seal rings with ATF, and install them to the transaxle rear cover.

    NOTICE:
    The rear clutch oil seal rings should be securely engaged in the grooves of the drum.


43. INSTALL NO. 1 TRANSAXLE CASE PLUG

  1. C134849
    Install 4 new O-rings to the 4 No. 1 transaxle case plugs.

  1. Install the 4 No. 1 transaxle case plugs to the transaxle rear cover.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


44. INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY

  1. D026454E01
    Remove any packing material and keep the contact surfaces of the transaxle rear cover and the transaxle case away from oil.

  1. Apply FIPG to the cover.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Apply FIPG in a continuous line (width 1.2 mm (0.047 in.)) along the sealing surface.

  1. C134848E01
    Apply adhesive or equivalent to the threads of bolt A.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the 11 bolts.

    Torque:
    Bolt A:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }
    Other bolts:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Apply adhesive to the bolts and tighten them within 10 minutes of application.


45. INSTALL NO. 2 UNDERDRIVE CLUTCH DISC

  1. C134879E01
    Coat the 3 discs with ATF.

  1. Install the 3 discs, 3 plates and flange to the transaxle case.

    NOTICE:
    Be careful about the order of discs, plates and flange.

  1. D026466E01
    Using a screwdriver, install the snap ring.

    NOTICE:
    The snap ring should be securely engaged in the groove of the drum.


46. INSPECT PACK CLEARANCE OF NO. 2 UNDERDRIVE CLUTCH

  1. D008082
    Using a dial indicator, measure the underdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    1.645 to 2.20 mm (0.0648 to 0.0866 in.)

  1. Select an appropriate flange from the table below so that the pack clearance will be within the specified range.

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    Y
    2.8 (0.110)
    C
    3.4 (0.134)
    A
    3.0 (0.118)
    D
    3.6 (0.142)
    B
    3.2 (0.126)
    -
    -

  1. Temporarily remove the snap ring and attach the flange to the transaxle case.

  1. Reinstall the snap ring to the transaxle case.


47. INSPECT UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003925E01
    Install the underdrive clutch assembly to the one-way clutch.

  1. Rotate the underdrive clutch assembly to check the rotating direction for the lock or free operation.

  1. Remove the underdrive clutch assembly from the one-way clutch.


48. INSTALL UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003907E01
    Install the outer race retainer to the one-way clutch.

    NOTICE:
    Securely install the outer race retainer onto the external tooth of the one-way clutch.

  1. C134880E01
    Install the one-way clutch to the transaxle case.

    NOTICE:
    Ensure that the outer race retainer and the mark on the transaxle case are aligned.

  1. D003581E01
    Using a screwdriver, install the snap ring to the transaxle case.

    NOTICE:
    The snap ring should be securely engaged in the groove of the transaxle case.


49. INSTALL UNDERDRIVE CLUTCH ASSEMBLY

  1. D003580
    Coat the bearing and bearing race with ATF, and install them onto the underdrive clutch.
    Bearing and bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing
    37.73 (1.4854)
    58.0 (2.284)
    Race
    29.9 (1.177)
    55.5 (2.185)

  1. Install the underdrive clutch assembly to the transaxle case.

    NOTICE:
    When installing the underdrive clutch drum sub-assembly, do not damage the oil seal ring.


50. INSTALL PARKING LOCK PAWL

  1. D009691E01
    Install the pawl pin and spring to the parking lock pawl.

  1. D026386
    Temporarily install the parking lock pawl, pin and spring to the transaxle case as shown in the illustration.


51. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. D003579E05
    Install the underdrive planetary gear assembly to the transaxle case.

    NOTICE:
    Firmly engage all the discs of the underdrive clutch with the hub splines of the underdrive planetary gear assembly and securely assemble them.

  1. D009693
    Install the parking lock pawl shaft.

  1. D003576E04
    Install the pawl shaft clamp with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. D003875E03
    Using a straight edge and vernier calipers as shown in the illustration, measure the gap between the top of the differential drive pinion in the underdrive planetary gear and contact surface of the transaxle case and housing (Dimension E).

    NOTICE:
    Note down dimension E because it is necessary for the following process.

  1. D025511E03
    As shown in the illustration, measure the 2 places of the transaxle housing, and calculate dimension F using the following formula.

    NOTICE:
    Note down dimension F because it is necessary for the following process.

    HINT:
    Dimension F = Dimension (1) - Dimension (2)


52. INSTALL MULTIPLE DISC CLUTCH HUB

  1. D008087E04
    Install the No. 1 thrust bearing race to the transaxle case while checking its direction.
    Bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing Race
    34.5 (1.359)
    48.5 (1.909)

  1. D026710E03
    Coat the thrust needle roller bearing and race with ATF, and install them onto the multiple disc clutch hub.
    Thrust bearing and race diameter: mm (in.) 

    Inside
    Outside
    Thrust Bearing
    36.4 (1.433)
    52.2 (2.055)

  1. Coat the needle roller bearing with ATF.

  1. D026711E03
    Install the needle roller bearing to the multiple disc clutch hub.
    Bearing diameter: mm (in.) 

    Inside
    Outside
    Bearing
    23.5 (0.925)
    44.0 (1.732)

  1. Install the multiple disc clutch hub to the transaxle case.


53. INSTALL FORWARD CLUTCH ASSEMBLY

  1. D003820E01
    Coat the thrust needle roller bearing with ATF.

  1. Install the thrust needle roller bearing to the forward clutch.

    Thrust bearing diameter: mm (in.) 

    Inside
    Outside
    Thrust Bearing
    33.85 (1.3327)
    52.2 (2.0551)

    NOTICE:
    Install the thrust bearing properly so that the temper colored side of the race will be visible.

  1. D003574E04
    Install the forward clutch to the forward clutch assembly.

    NOTICE:
    1. Align the splines of all discs in the forward clutch with those of the multiple clutch hub to assemble them securely.
    2. Be careful not to damage the bush inside the forward clutch hub during installation.


54. INSTALL OVERDRIVE BRAKE GASKET

  1. D003573
    Install 2 new overdrive brake gaskets.


55. INSTALL DIFFERENTIAL GEAR ASSEMBLY

  1. D026450E07
    Install the differential gear assembly to the transaxle case.


56. INSTALL NO. 2 THRUST BEARING UNDERDRIVE RACE

  1. D025506E05
    Install the No. 2 thrust bearing underdrive race to the underdrive planetary gear assembly.


57. INSTALL THRUST NEEDLE ROLLER BEARING

  1. D025505E04
    Coat the thrust needle roller bearing with ATF.

  1. Calculate the end play value using the formula below and values of Dimensions E and F that ware measured when installing the cylindrical roller bearing and underdrive planetary gear. Select an appropriate underdrive planetary gear thrust bearing race No. 2 which satisfies the specified end play value, and install it.

    End play:
    0.198 to 0.693 mm (0.00779 to 0.02728 in.)

    HINT:
    End play = Dimension F - Dimension E - Thrust bearing thickness 2.5 mm (0.0984 in.) - Underdrive thrust bearing race No. 2 thickness.

    Race thickness: mm (in.) 
    F - E
    Thickness
    Less than 7.339 (0.28894)
    3.5 (0.138)
    7.339 (0.28894) or more
    3.8 (0.150)
    Bearing and bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing
    53.0 (2.087)
    78.2 (3.079)
    Bearing race
    52.1 (2.051)
    75.5 (2.972)


58. INSTALL OIL PUMP ASSEMBLY

  1. D003569E03
    Install the oil pump to the transaxle case with the 7 bolts.

    Torque:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }

  1. D003629E04
    Coat the O-ring of the oil pump with ATF.

    NOTICE:
    Confirm the input shaft rotates smoothly with the manual operation after installing the oil pump.


59. INSTALL TRANSAXLE HOUSING

  1. D003630E09
    Remove any parking material and keep the contact surfaces of the transaxle case and transaxle housing away from oil.

  1. Apply FIPG to the transaxle case.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. C147840E01
    Install the transaxle housing to the transaxle case with the 18 bolts.

    Torque:
    Bolt A:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }
    Bolt B,C:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    Bolt D:
    10 N*m{ 101 kgf*cm , 7 ft.*lbf }

    HINT:
    Apply adhesive or equivalent to bolts A and C.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
    Bolt length:
    Bolt A,B,D:
    50 mm (1.969 in.)
    Bolt C:
    42 mm (1.654 in.)

    NOTICE:
    Apply adhesive to the bolts and tighten them within 10 minutes of application.


60. INSPECT INPUT SHAFT END PLAY

  1. D008091
    Using a dial indicator, measure the input shaft end play.

    End play:
    0.262 to 1.244 mm (0.01 to 0.049 in.)


61. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

  1. D003631
    Support the transaxle assembly.


62. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. D026468E01
    Coat a new oil seal with MP grease.

  1. Using SST, install the oil seal to the transaxle case.

    SST
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in. )


63. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. C134844E01
    Install the parking lock rod to the manual valve lever.

    HINT:
    Align the dial with the notches on the manual valve lever and turn the dial 90° to install the parking lock rod.


64. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

  1. C134881
    Install a new spacer and the manual valve lever shaft to the transaxle case.

    NOTICE:
    Do not damage the oil seal while installing the shaft to the transaxle case.

  1. C134843
    Using a pin punch and hammer, drive in a new pin.

  1. D026765E02
    Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.


65. INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING

  1. D003559
    Using needle-nose pliers, install the retainer spring.

    NOTICE:
    Hang the spring on the shaft securely.


66. INSTALL PARKING LOCK PAWL BRACKET

  1. D003561E01
    Install the parking lock pawl bracket with the 2 bolts.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

    Bolt length:
    25 mm (0.98 in.)

    NOTICE:
    Be sure the parking rod is placed between the parking pawl and the guide of the parking bracket after the parking bracket is installed.


67. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

  1. D003560E04
    Install the manual detent spring sub-assembly with the 2 bolts.

    NOTICE:
    Make sure to install the manual detent spring and cover in this order.

    HINT:
    Tighten the bolts in the order of A and B.

    Torque:
    Bolt A:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }
    Bolt B:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    Bolt length:
    Bolt A:
    27 mm (1.06 in.)
    Bolt B:
    16 mm (0.63 in.)


68. INSTALL B-3 ACCUMULATOR PISTON

  1. D003904E06
    Coat a new O-ring with ATF, and install it to the B-3 accumulator piston.

    NOTICE:
    Make sure that the O-ring is not twisted or pinching. Apply enough ATF to the O-ring prior to installation. Be sure about the installation position.

  1. D025512E01
    Coat the piston and springs with ATF, and install them to the transaxle case.

    NOTICE:
    Install the correct springs to the B-3 accumulator piston by checking the color or dimension of the springs.

    Accumulator spring: 
    Free length / Outer diameter (mm (in.))
    Color
    Inner: 62.00 (2.4409) / 15.50 (0.610)
    Purple
    Outer: 74.23 (2.9224) / 21.70 (0.854)
    Purple


69. INSTALL REVERSE CLUTCH ACCUMULATOR PISTON

  1. D026402E06
    Coat 2 new O-rings with ATF, and install them to the reverse clutch accumulator piston.

    NOTICE:
    Make sure that the O-ring is not twisted or pinching. Apply enough ATF to the O-rings prior to installation. Be sure about the installation positions.

  1. C092978
    Coat the piston and spring with ATF, and install them to the transaxle case.

    NOTICE:
    Install the correct spring to the reverse clutch accumulator piston by checking the color or dimension of the spring.

    Accumulator spring: 
    Free length / Outer diameter (mm (in.))
    Color
    60.96 (2.3999) / 14.10 (0.555)
    Yellow


70. INSTALL C-3 ACCUMULATOR PISTON

  1. C134841E01
    Coat a new O-ring with ATF, and install it to the C-3 accumulator piston.

    NOTICE:
    Make sure that the O-ring is not twisted or pinching. Apply enough ATF to the O-ring prior to installation. Be sure about the installation position.

  1. C083146
    Coat the piston with ATF, and install it to the transaxle case.

  1. D003555
    Install the spring to the C-3 accumulator piston.

    NOTICE:
    Install the correct spring to the C-3 accumulator piston by checking the color or dimension of the spring.

    Accumulator spring: 
    Free length / Outer diameter (mm (in.))
    Color
    72.20 (2.8425) / 19.0 (0.748)
    Colorless


71. INSTALL CHECK BALL BODY

  1. D003554E01
    Coat the check ball body with ATF.

  1. Install the check ball body and spring.

    NOTICE:
    Regarding the installation of the spring for the check ball body, be sure to place the spring in the hole in the ball body. Be careful about the orientation of the parts.


72. INSTALL BRAKE DRUM GASKET

  1. C083129
    Coat a new brake drum gasket with ATF, and install it to the transaxle case.

    NOTICE:
    Do not damage the lip portion of the brake drum gasket when inserting the gasket to the case. Apply enough ATF to the gasket prior to installation. Be careful about the orientation of the parts.


73. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

  1. C083128
    Coat a new transaxle case 2nd brake gasket with ATF, and install it to the transaxle case.

    NOTICE:
    Do not damage the lip portion of the transaxle case 2nd brake gasket when inserting the gasket to the case. Apply enough ATF to the gasket prior to installation. Be careful about the orientation of the parts.


74. INSTALL NO. 1 GOVERNOR APPLY GASKET

  1. C083127
    Coat a new No. 1 governor apply gasket with ATF, and install it to the transaxle case.

    NOTICE:
    Do not damage the lip portion of the No. 1 governor apply gasket when inserting the gasket to the case. Apply enough ATF to the gasket prior to installation. Be careful about the orientation of the parts.


75. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. C091933E05
    Check the manual valve lever position. Install the valve body to the transaxle case with the 17 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    25 mm (0.984 in.)
    Bolt B:
    57 mm (2.244 in.)
    Bolt C:
    41 mm (1.614 in.)

    NOTICE:
    1. Push the valve body against the accumulator piston spring and the check ball body to install it.
    2. When installing the valve body to the transaxle case, do not hold the solenoids.
    3. Temporarily tighten the bolts marked by (1) in the illustration first because they are positioning bolts.


76. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

  1. C091932E02
    Coat a new O-ring with ATF, and install it to the oil strainer.

    NOTICE:
    Make sure that the O-ring is not twisted or pinching. Apply enough ATF to the O-ring prior to installation.

  1. C134839
    Install the oil strainer to the valve body with the 3 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    Apply ATF to the bolts prior to installation.


77. INSTALL TRANSMISSION WIRE

  1. D003636E06
    Coat a new O-ring with ATF, and install it to the transmission wire.

    NOTICE:
    Make sure that the O-ring is not twisted or pinching. Apply enough ATF to the O-ring prior to installation.

  1. D003547E05
    Install the transmission wire retaining bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


78. CONNECT TRANSMISSION WIRE

  1. C091927E06
    Coat an O-ring of the ATF temperature sensor with ATF.

  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }

  1. Connect the 7 solenoid connectors.

    NOTICE:
    1. Connect the connectors to A, B, C, D, E, F and G, starting with the shorter ones.
    2. Apply ATF to the bolt prior to installation.


79. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. C134837E01
    Install the 2 magnets in the oil pan.

  1. Apply adhesive or equivalent to the 18 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C091925
    Install a new oil pan gasket and the oil pan to the transaxle case with the 18 bolts.

    Torque:
    7.8 N*m{ 79 kgf*cm , 69 in.*lbf }

    NOTICE:
    1. Apply adhesive to the bolts and tighten them within 10 minutes of application.
    2. Remove any oil or grease from the contact surface of the transaxle case and the oil pan with the gasket completely before installing the oil pan to the case.

  1. Install a new gasket to the drain plug.

  1. Install the drain plug.

    Torque:
    49 N*m{ 499 kgf*cm , 36 ft.*lbf }


80. INSTALL NO. 1 TRANSAXLE CASE PLUG

  1. D026716
    Coat 4 new O-rings with ATF, and install them to the 4 No. 1 transaxle case plugs.

  1. Install the 4 No. 1 transaxle case plugs to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


81. INSTALL SPEED SENSOR

  1. D030672E04
    Apply liquid sealer to the "A" bolt threads.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the 2 sensors to the transaxle case with the 2 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


82. INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

  1. C083144E04
    Coat a new O-ring with ATF, and install it to the union.

  1. Install the union to the transaxle case.

    Torque:
    27 N*m{ 276 kgf*cm , 20 ft.*lbf }


83. INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

  1. C083143E03
    Coat a new O-ring with ATF, and install it to the union.

  1. Install the union to the transaxle case.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


84. INSTALL NO. 2 BREATHER PLUG
  1. Coat a new O-ring with ATF.

  1. C134834E01
    Install the hose and a new O-ring to the breather plug.

  1. Install the No. 2 breather plug hose to the transaxle case.


85. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C135710
    Install the park/neutral position switch onto the manual valve lever shaft and temporarily install the 2 adjusting bolts.

  1. Install a new nut stopper and nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. C135709
    Temporarily install the control shaft lever.

  1. C135711
    Turn the lever counterclockwise until it stops, and then turn it clockwise 2 notches.

  1. Remove the control shaft lever.

  1. C099456E01
    Align the groove with the neutral basic line.

  1. Hold the switch in position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C135708
    Using a screwdriver, stake the nut with the nut stopper.

  1. C135707
    Install the control shaft lever, washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Jun 2006)COMPONENTS (from Jun 2006) →