2006-2011 Camry Aurion · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Jun 2006


1. INSTALL REVERSE GEAR

  1. C069672
    Coat the reverse gear with gear oil.

  1. Install the 3 No. 1 synchromesh shifting key springs and No. 1 transmission clutch hub to the reverse gear.

    NOTICE:
    Assemble the reverse gear and the No. 1 transmission clutch hub in the correct direction.

  1. Using a screwdriver, install the 3 No. 1 synchromesh shifting keys to the reverse gear.


2. INSTALL OUTPUT SHAFT FRONT BEARING

  1. C092874E02
    Using SST and a press, install the output shaft front bearing (inner race) to the output shaft.
    SST
    09950-60010   (09951-00430)
    09950-70010   (09951-07150)


3. INSTALL NO. 1 SYNCHRONIZER RING SET

  1. C069649
    Coat the No. 1 synchronizer ring set with gear oil and install it to the 1st gear.

    NOTICE:
    Align the No. 1 synchronizer ring set with the hole of the 1st gear.


4. INSTALL 1ST GEAR NEEDLE ROLLER BEARING

  1. C069650
    Coat the 1st gear needle roller bearing with gear oil and install it to the output shaft.


5. INSTALL 1ST GEAR

  1. C069673
    Coat the 1st gear with gear oil and install it to the output shaft.


6. INSTALL NO. 1 TRANSMISSION CLUTCH HUB

  1. C092862E02
    Using SST and a press, install the No. 1 transmission clutch hub to the output shaft.
    SST
    09316-60011   (09316-00031)
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    1. Align the No. 1 synchronizer ring with the No. 1 synchromesh shifting key.
    2. Make sure that the 1st gear rotates.


7. INSTALL 2ND GEAR BUSHING BALL

  1. C083814
    Coat the gear bushing with MP grease, and install it to the output shaft.


8. INSTALL 2ND GEAR BUSHING

  1. C069646
    Coat the 2nd gear bushing with gear oil and install it to the output shaft.


9. INSTALL 2ND GEAR BEARING SPACER

  1. C069645
    Coat the 2nd gear bearing spacer with gear oil and install it to the output shaft.


10. INSTALL 2ND GEAR NEEDLE ROLLER BEARING

  1. C069644
    Coat the 2nd gear needle roller bearing with gear oil and install it to the output shaft.


11. INSTALL NO. 2 SYNCHRONIZER RING SET

  1. C069643
    Coat the No. 2 synchronizer ring set with gear oil and install it to the No. 1 transmission clutch hub.

    NOTICE:
    Align the key groove on the No. 2 synchronizer ring set with the No. 1 synchromesh shifting key.


12. INSTALL 2ND GEAR

  1. C069679
    Coat the 2nd gear with gear oil and install it to the output shaft.


13. INSTALL 3RD DRIVEN GEAR

  1. C092863E02
    Using SST and a press, install the 3rd driven gear to the output shaft.
    SST
    09608-00071  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)


14. INSTALL OUTPUT GEAR SPACER

  1. C069641
    Install the output gear spacer to the output shaft.


15. INSTALL 4TH DRIVEN GEAR

  1. C092864E03
    Using SST and a press, install the 4th driven gear to the output shaft.
    SST
    09608-00071  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)


16. INSTALL OUTPUT SHAFT FRONT BEARING

  1. C092865E02
    Using SST and a press, install the output shaft front bearing (inner race) to the output shaft.
    SST
    09506-30012  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

← INSPECTION (from Jun 2006)COMPONENTS (from Jun 2006) →