2006-2011 Camry Aurion · Service Manual CRUISE CONTROL SYSTEM

P0571 Brake Switch "A" Circuit

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP SW fuse and the stop light switch, and the ECM turns the cruise control off.
DTC No.
DTC Detection Condition
Trouble Area
P0571
When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 sec. or more
  1. Stop light switch
  2. Stop light switch circuit
  3. ECM

WIRING DIAGRAM

E141639E01
E141645E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG), and turn the intelligent tester main switch on.

  1. Check the DATA LIST for proper functioning of the stop light switch.

    ECM (Cruise control): 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Stp Light SW M
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stp Light SW S1
    Stop light switch signal (Sub CPU)
    Terminal: STP / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stp Light SW S2
    Stop light switch signal (Sub CPU)
    Terminal: ST1- / ON or OFF
    ON: Brake pedal released
    OFF: Brake pedal depressed
    -

    OK:
    When the brake pedal is operated, the display changes as shown above.



OK
REPLACE ECM (Click here)
NG


2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)

  1. E135377E03
    Disconnect the A19 connector from the stop light switch.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A19-2 - Body ground
    Always
    10 to 14 V
    A19-3 - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STOP LIGHT SWITCH

  1. E128781E01
    Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    1 - 2
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin pushed
    Below 1 Ω

  1. Install the stop light switch (Click here).



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


4. CHECK ECM

  1. E135382E13
    Reconnect the stop light switch connector.

  1. Disconnect the A55 connector from the ECM. (LHD)

  1. Disconnect the A24 connector from the ECM. (RHD)

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LHD:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    A55-36 (STP) - Body ground
    Depressed
    10 to 14 V
    A55-36 (STP) - Body ground
    Released
    Below 1 V
    A55-35 (ST1-) - Body ground
    Depressed
    Below 1 V
    A55-35 (ST1-) - Body ground
    Released
    10 to 14 V
    RHD:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    A24-36 (STP) - Body ground
    Depressed
    10 to 14 V
    A24-36 (STP) - Body ground
    Released
    Below 1 V
    A24-35 (ST1-) - Body ground
    Depressed
    Below 1 V
    A24-35 (ST1-) - Body ground
    Released
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)
OK

REPLACE ECM (Click here)


← P0500 Vehicle Speed Sensor Malfunction (+ P0503) (from Jun 2009)P0571 Brake Switch "A" Circuit (from Jun 2009) →