Driver Side Door Key Lock and Unlock Switch Circuit
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The driver's door key lock and unlock switch is built into the driver's door lock assembly.When the driver's door key cylinder is turned to lock all the doors by the key, there is continuity between terminals L and E of the key lock and unlock switch. When the cylinder is turned to unlock the door(s), there is continuity between terminals UL and E.
Terminals L2 and UL2 of the main body ECU (instrument panel J/B) are connected to the door lock assembly, and door lock/unlock request signals (by key) are input to the main body ECU (instrument panel J/B).
The main body ECU (instrument panel J/B) constantly applies voltage to terminal L of the driver's door lock assembly via terminal L2. When the driver's door key cylinder is turned to lock all the doors by the key, current flows from terminal L2 to terminal L.
The main body ECU (instrument panel J/B) also applies constant voltage to terminal UL of the door lock assembly via terminal UL2. When the door key cylinder is turned in the direction to unlock the door(s) by the key, current flows from terminal UL2 to terminal UL.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE ON INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.


Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select Door Key SW-Lock and Door Key SW-Unlock in the DATA LIST, and read the tester display.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key SW-Lock
Driver door lock/unlock switch lock signal (key-linked lock switch)
/ON or OFF
ON: Driver side door key cylinder is turned to LOCK
OFF: Driver side door key cylinder is not turned to LOCK
-
Door Key SW-Unlock
Driver door lock/unlock switch unlock signal (key-linked unlock switch)
/ON or OFF
ON: Driver side door key cylinder is turned to UNLOCK
OFF: Driver side door key cylinder is not turned to UNLOCK
-
- OK:
- The display is as specified in the "Normal Condition" column.
|
|
||||
| OK | ||
| ||
| 2. INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR KEY LOCK AND UNLOCK SWITCH) |
for LHD:
Remove the front door lock assembly LH (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
7 - 9
ON (Door lock set to LOCK)
Below 1 Ω
7 - 9
7 - 10
OFF (Free)
10 kΩ or higher
7 - 10
ON (Door lock set to UNLOCK)
Below 1 Ω
for RHD:
Remove the front door lock assembly RH (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
8 - 6
ON (Door lock set to LOCK)
Below 1 Ω
8 - 6
8 - 5
OFF (Free)
10 kΩ or higher
8 - 5
ON (Door lock set to UNLOCK)
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU) |
Disconnect the instrument panel J/B connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
(Symbols)
Condition
Specified Condition
I7-9 (L) - IK-16
Always
Below 1 Ω
I7-10 (UL) - E7-10 (UL3)
Always
Below 1 Ω
I7-7 (E) - Body ground
Always
Below 1 Ω
I7-9 (L) - Body ground
Always
10 kΩ or higher
I7-10 (UL) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
(Symbols)
Condition
Specified Condition
H8-6 (L) - IJ-5
Always
Below 1 Ω
H8-5 (UL) - E7-10 (UL3)
Always
Below 1 Ω
H8-8 (E) - Body ground
Always
Below 1 Ω
H8-6 (L) - Body ground
Always
10 kΩ or higher
H8-5 (UL) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
