2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

ADJUSTMENT

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    for Australia: 
    Tire size
    Front kPa (kgf*cm2, psi)
    Rear kPa (kgf*cm2, psi)
    215/60R16 95V
    4 passengers or less
    210 (2.1, 31)*1, 230 (2.3, 33)*2
    210 (2.1, 31)*1, 230 (2.3, 33)*2
    5 passengers
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    215/55R17 93V
    4 passengers or less
    220 (2.2, 32)*1, 250 (2.5, 36)*2
    220 (2.2, 32)*1, 250 (2.5, 36)*2
    5 passengers
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    240 (2.4, 35)*1, 300 (3.1, 44)*2

    *1: For driving at under 140 km/h (87 mph).
    *2: For driving at over 140 km/h (87 mph).

    Cold tire inflation pressure:
    for GCC: 
    Tire size
    Front kPa (kgf*cm2, psi)
    Rear kPa (kgf*cm2, psi)
    215/60R16 95V
    210 (2.1, 31)*1, 240 (2.4, 35)*2
    210 (2.1, 31)*1, 240 (2.4, 35)*2
    215/55R17 93V
    220 (2.2, 32)*1, 240 (2.4, 35)*2
    220 (2.2, 32)*1, 240 (2.4, 35)*2

    *1: For driving at under 160 km/h (100 mph).
    *2: For driving at over 160 km/h (100 mph).

  1. C137874
    Using a dial indicator, check the runout of the tires.

    Tire runout:
    1.4 mm (0.055 in.) or less


2. MEASURE VEHICLE HEIGHT

  1. C132408E01
    Bounce the vehicle up and down at the corners to stabilize the suspension. Inspect the vehicle height.

    Vehicle height:
    for Australia 
    Model
    Front A - B
    Rear C - D
    ACV40R-DEADKQ
    129 mm (5.08 in.)
    44 mm (1.73 in.)
    ACV40R-DEAGKQ
    ACV40R-DEANKQ
    ACV40R-DEAVKQ
    131 mm (5.16 in.)
    49 mm (1.93 in.)
    ACV40R-DEMDKQ
    121 mm (4.76 in.)
    45 mm (1.77 in.)
    ACV40R-DEMVKQ
    125 mm (4.92 in.)
    51 mm (2.01 in.)
    GSV40R-JETDKQ
    128 mm (5.04 in.)
    47 mm (1.85 in.)
    GSV40R-JETGKQ
    GSV40R-JETNKQ
    GSV40R-JETSKQ
    130 mm (5.12 in.)
    51 mm (2.01 in.)
    GSV40R-JETVKQ
    for Papua New Guinea and Fiji 
    Model
    Front A - B
    Rear C - D
    ACV40R-DEANKQ
    119 mm (4.69 in.)
    35 mm (1.38 in.)
    GSV40R-JETNKQ
    for GCC 
    Model
    Front A - B
    Rear C - D
    ACV40L-DEADKV
    129 mm (5.08 in.)
    44 mm (1.73 in.)
    ACV40L-DEANKV
    ACV40L-DEASKV
    131 mm (5.16 in.)
    49 mm (1.93 in.)
    ACV40L-DEMDKV
    121 mm (4.76 in.)
    45 mm (1.77 in.)
    ACV40L-DEMNKV
    ACV40L-DEMSKV
    125 mm (4.92 in.)
    51 mm (2.01 in.)
    GSV40L-JETDKV
    128 mm (5.04 in.)
    47 mm (1.85 in.)
    GSV40L-JETGKV

    Measuring points:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of lower suspension arm No. 2 bushing set bolt center
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of strut rod set bolt center

    NOTICE:
    1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
    2. Be sure to perform measurement on a level surface.
    3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.


3. INSPECT TOE-IN

  1. C148261E01
    Bounce the vehicle up and down at the corners to stabilize the suspension. Inspect the toe-in.

    Toe-in:
    for Australia 
    Toe-in
    -
    C - D:
    4 +- 2 mm (0.16 +- 0.08 in.)
    for GCC 
    Toe-in
    -
    C - D:
    3 +- 1 mm (0.12 +- 0.04 in.)

    If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.


4. ADJUST TOE-IN

  1. C132497
    Measure the lengths of the right and left rear No. 2 suspension arms.

    Difference in the length between the right and left rear No. 2 suspension arms:
    1.5 mm (0.06 in.) or less

    If the left-right difference is larger than 1.5 mm (0.06 in.), adjust it by following the procedures below.

  1. C132498
    Loosen the lock nuts.

  1. Turn the right and left adjusting tubes by an equal amount to adjust toe-in.

    HINT:
    1. Try to adjust toe-in to the center of the specified range.
    2. One turn of each adjusting tube will adjust toe-in by approximately 10.8 mm (0.425 in.).

  1. Tighten the lock nuts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }


5. INSPECT CAMBER

Camber:
for Australia 
Model
Camber
Right-left difference
ACV40R-DEADKQ
-1°10' +-45' (-1.17° +-0.75°)
45' (0.75°) or less
ACV40R-DEAGKQ
ACV40R-DEANKQ
ACV40R-DEMDKQ
ACV40R-DEAVKQ
-1°15' +-45' (-1.25° +-0.75°)
ACV40R-DEMVKQ
GSV40R-JETDKQ
-1°15' +-45' (-1.25° +-0.75°)
GSV40R-JETGKQ
GSV40R-JETNKQ
GSV40R-JETSKQ
-1°15' +-45' (-1.25° +-0.75°)
GSV40R-JETVKQ
for Papua New Guinea and Fiji 
Model
Camber
Right-left difference
ACV40R-DEANKQ
-1°00' +-45' (-1.00° +-0.75°)
45' (0.75°) or less
GSV40R-JETNKQ
for GCC 
Model
Camber
Right-left difference
ACV40L-DEADKV
-1°10' +-45' (-1.17° +-0.75°)
45' (0.75°) or less
ACV40L-DEANKV
ACV40L-DEMNKV
ACV40L-DEMDKV
ACV40L-DEASKV
-1°15' +-45' (-1.25° +-0.75°)
ACV40L-DEMSKV
GSV40L-JETDKV
-1°15' +-45' (-1.25° +-0.75°)
GSV40L-JETGKV

HINT:
Camber is not adjustable. If the measurement is not within the specification range, inspect the suspension parts for damage and/or wear, and replace them if necessary.

← ADJUSTMENT (Jun 2006 – Sep 2006)ADJUSTMENT (from Jun 2009) →