2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.
If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as to if the switch were continuously pressed. Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

E212465E01

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E168561E53
    Disconnect the navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F38-7 (SW1) - F38-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    F38-7 (SW1) - F38-6 (SWG)
    Seek+ switch pushed
    Below 2.5 Ω
    F38-7 (SW1) - F38-6 (SWG)
    Seek- switch pushed
    312.5 to 345.4 Ω
    F38-7 (SW1) - F38-6 (SWG)
    Volume+ switch pushed
    950 to 1050 Ω
    F38-7 (SW1) - F38-6 (SWG)
    Volume- switch pushed
    2954.5 to 3265.5 Ω
    F38-7 (SW1) - F38-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    F38-7 (SW1) - F38-6 (SWG)
    MODE switch pushed
    Below 2.5 Ω
    F38-7 (SW1) - F38-6 (SWG)
    Voice switch pushed
    2954.5 to 3265.5 Ω
    F38-7 (SW1) - F38-6 (SWG)
    On Hook switch pushed
    312.5 to 345.4 Ω
    F38-7 (SW1) - F38-6 (SWG)
    Off Hook switch pushed
    950 to 1050 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Receiver Assembly)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E168547E08
    Disconnect the steering pad switch assembly and spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-10 (AU1) - E18-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-9 (AU2) - E18-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY

  1. Disconnect the steering pad switch assembly connector.E129804E04

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-10 (AU1) - a1-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    a1-10 (AU1) - a1-8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    a1-10 (AU1) - a1-8 (EAU)
    Seek- switch pushed
    312.5 to 345.4 Ω
    a1-10 (AU1) - a1-8 (EAU)
    Volume+ switch pushed
    950 to 1050 Ω
    a1-10 (AU1) - a1-8 (EAU)
    Volume- switch pushed
    2954.5 to 3265.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    a1-9 (AU2) - a1-8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    Voice switch pushed
    2954.5 to 3265.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    On Hook switch pushed
    312.5 to 345.4 Ω
    a1-9 (AU2) - a1-8 (EAU)
    Off Hook switch pushed
    950 to 1050 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch Assembly for 3 Spoke Type)
    *2
    Component without harness connected
    (Steering Pad Switch Assembly for 4 Spoke Type)
    *3
    Volume-
    *4
    Volume+
    *5
    Seek-
    *6
    Seek+
    *7
    MODE
    *8
    Off Hook
    *9
    On Hook
    *10
    Voice



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)


← Steering Pad Switch Circuit (Oct 2006 – May 2009)Illumination Circuit (Jun 2006 – Sep 2006) →