Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.
Disconnect the connector.
Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.
Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.
5.
REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
Using a screwdriver with the tip wrapped with protective tape, disengage the 2 claws and remove the rear power window regulator switch assembly.
6.
REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.
7.
REMOVE REAR DOOR ARMREST BASE PANEL UPPER
Remove the 7 screws.
Disengage the 4 claws and remove the rear door armrest base panel upper.
8.
REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Disconnect the cables and remove the rear door inside handle sub-assembly.
9.
REMOVE REAR DOOR SERVICE HOLE COVER
Disconnect the connector.
Remove the rear door service hole cover.
HINT:
Remove the remaining tape on the door side.
10.
REMOVE REAR DOOR CHECK ASSEMBLY
Remove the bolt, 2 nuts, and the rear door check assembly.
11.
REMOVE REAR DOOR WEATHERSTRIP
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
12.
REMOVE REAR DOOR GLASS RUN
Remove the rear door glass run.
13.
REMOVE REAR DOOR FRAME GARNISH
Disengage the clip and remove the rear door frame garnish.
14.
REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY
Remove the 2 bolts, the screw, and the rear door lower window frame sub-assembly.
15.
REMOVE REAR DOOR QUARTER WINDOW GLASS
Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
16.
REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
NOTICE:
Do not damage the door glass.
17.
REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
Disconnect the connector.
Loosen the temporary bolt.
NOTICE:
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall, causing damage.
Remove the 3 bolts.
Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.
Remove the temporary bolt from the rear door window regulator.
18.
REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.
19.
REMOVE REAR DOOR LOCK ASSEMBLY
Using a "TORX" socket wrench (T30), remove the 3 screws.
Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.
Remove the door lock wiring harness seal from the rear door lock assembly.
20.
REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Using a screwdriver, disengage the claw.
HINT:
Tape the screwdriver tip before use.
Remove the rear door lock remote control cable assembly.
21.
REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
Using a screwdriver, disengage the 3 claws.
HINT:
Tape the screwdriver tip before use.
Remove the rear door inside locking cable assembly.
22.
REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using a "TORX" socket wrench (T30), loosen the screw.
HINT:
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.
Disengage the 2 claws and remove the rear door outside handle cover.
23.
REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
Pull and hold the release plate of the outside handle frame as shown in the illustration.
NOTICE:
The release plate may interfere with the outside handle and may be damaged when removing the handle, unless the release plate of the outside handle frame is pulled and held.
Remove the rear door outside handle assembly as shown in the illustration.
24.
REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws and remove the rear door front outside handle pad.
25.
REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Disengage the 2 claws and remove the rear door rear outside handle pad.
26.
REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Using a "TORX" socket wrench (T30), remove the screw.
Disengage the claw and remove the rear door outside handle frame sub-assembly.
27.
REMOVE REAR DOOR BELT MOULDING ASSEMBLY
Fully open the rear door glass.
Put protective tape around the rear door belt moulding assembly.
Using a moulding remover, disengage the clip and 6 claws, and remove the rear door belt moulding assembly.
HINT:
Tape the remover tip before use.
NOTICE:
Be careful when removing the moulding as there are claws attached to the front end of the moulding.
28.
REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING
HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.
Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body and moulding excessively.
Using a heat light, heat the rear door front window frame moulding.
Disengage the clip.
Using a moulding remover, remove the rear door front window frame moulding.
29.
REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
Put a 4 mm (0.16 in.) drill bit into a drill.
Tape the drill bit without the portion of 5 mm (0.20 in.) from the tip covered.
HINT:
Tape the drill bit to prevent the drill bit from going too deep.
Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 7 rivets.
NOTICE:
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.
Be careful when touching the drilled rivets, as they may become hot.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Remove the rear door upper window frame moulding from the door frame.
30.
REMOVE REAR DOOR OUTSIDE STRIPE
Using a heat light, heat the rear door outside stripe.
Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
NOTICE:
Do not heat the vehicle body excessively.
Pull back an edge of the rear door outside stripe and pull it parallel to the vehicle body to pull it off.
31.
REMOVE REAR DOOR LOWER OUTSIDE STRIPE
Using a heat light, heat the rear door lower outside stripe.
Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
NOTICE:
Do not heat the vehicle body excessively.
Pull back an edge of the rear door lower outside stripe and pull it parallel to the vehicle body to pull it off.