2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Ignition Switch Circuit

Circuit diagnosis · Vehicles built Jun 2006 – May 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit detects the state of the ignition switch, and sends it to the main body ECU.

WIRING DIAGRAM

E121497E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select the items below in the DATA LIST, and read the display on the intelligent tester.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Ignition switch ACC signal / ON or OFF
    ON: Ignition switch ON or ACC
    OFF: Ignition switch off
    -
    IG SW
    Ignition switch IG signal / ON or OFF
    ON: Ignition switch ON or ACC
    OFF: Ignition switch off
    -

    OK:
    Normal conditions listed above are displayed.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT ACC RELAY

  1. B087894E05
    Remove the ACC relay from the instrument panel J/B assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω (When battery voltage is applied to terminals 1 and 2)



NG
REPLACE ACC RELAY
OK


3. INSPECT NO. 1 IGNITION RELAY

  1. B087894E05
    Remove the No. 1 ignition relay from the instrument panel J/B assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω (When battery voltage is applied to terminals 1 and 2)



NG
REPLACE NO. 1 IGNITION RELAY
OK


4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B ASSEMBLY - BATTERY AND GROUND)

  1. E121505E01
    Disconnect the IA instrument panel J/B assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IA-1 - Body ground
    Always
    10 to 14 V

  1. E121504E01
    Disconnect the IF instrument panel J/B assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IF-10 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B ASSEMBLY - IGNITION SWITCH)

  1. E121503E01
    Disconnect the E23 ignition switch connector.

  1. Disconnect the II instrument panel J/B assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    II-3 - E23-2 (ACC)
    Always
    Below 1 Ω
    II-4 - E23-4 (AM1)
    Always
    Below 1 Ω
    II-9 - E23-1 (IG1)
    Always
    Below 1 Ω
    II-3 - Body ground
    Always
    10 kΩ or higher
    II-4 - Body ground
    Always
    10 kΩ or higher
    II-9 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here)

    OK:
    Ignition switch is normal.



NG
REPLACE IGNITION SWITCH
OK

REPLACE INSTRUMENT PANEL J/B ASSEMBLY


← B1244 Light Sensor Circuit Malfunction (from Jun 2009)Ignition Switch Circuit (from Jun 2009) →