2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

B2416 Height Control Sensor Malfunction

Diagnostic trouble codes · Vehicles built from Oct 2006

DESCRIPTION

The AFS ECU receives signals indicating the height of the vehicle from the rear height control sensor.
DTC No.
DTC Detecting Condition
Trouble Area
B2416
  1. Malfunction in rear height control sensor sub-assembly
  2. Open or short in rear height control sensor circuit
  1. Rear height control sensor
  2. Harness or connector
  3. AFS ECU

WIRING DIAGRAM

B110590E06

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the items below in the DATA LIST, and read the display on the intelligent tester.

    AFS ECU: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Rr Height Sens
    Rear height control sensor signal value / 0 to 5 V
    Approx. 2.5 V
    -
    Height Sens Val
    Rear height control sensor power supply value / 0 to 5 V
    Approx. 5.0 V
    -

    OK:
    Normal conditions listed above are displayed.



OK
REPLACE AFS ECU
NG


2. CHECK HARNESS AND CONNECTOR (AFS ECU - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)

  1. E133251E04
    Disconnect the A61 AFS ECU connector.

  1. Disconnect the O23 rear height control sensor sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A61-18 (A6M) - O23-3 (SHB)
    Always
    Below 1 Ω
    A61-19 (A6E) - O23-2 (SHRR)
    Always
    Below 1 Ω
    A61-21 (A6N) - O23-1 (SHG)
    Always
    Below 1 Ω
    A61-18 (A6M) - Body ground
    Always
    10 kΩ or higher
    A61-19 (A6E) - Body ground
    Always
    10 kΩ or higher
    A61-21 (A6N) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT AFS ECU

  1. E133228E07
    Reconnect the A61 AFS ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Condition
    Condition
    Specified Condition
    A61-18 (A6M) - A61-21 (A6N)
    Ignition switch on (IG)
    4.5 to 5.5 V



NG
REPLACE AFS ECU
OK


4. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

  1. E121521E03
    Connect 3 dry cell batteries (1.5 V) in series.

  1. Remove the rear height control sensor sub-assembly.

  1. Connect the positive (+) lead from the battery to terminal 3, and the negative (-) lead from the battery to terminal 1.

  1. Measure the voltage between terminals 2 and 1 while slowly moving the link up and down.

    Standard voltage:
    Tester Condition
    Condition
    Specified Condition
    2 (SHRR) - 1 (SHG)
    +45°(High)
    Approx. 4.05 V
    0°(Normal)
    Approx. 2.25 V
    -45°(Low)
    Approx. 0.45 V



NG
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
OK

REPLACE AFS ECU


← B2415 Vehicle Speed Sensor Malfunction (from Jun 2009)B2417 Headlight Beam Level Control Motor LH Malfunction (+ B2418) (from Oct 2006) →