2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Rear Door UNLOCK Detection Switch RH Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The rear right door unlock detection switch is built into the rear right door lock assembly. The switch turns on when the rear right door is locked and turns off when the door is unlocked.
The main body ECU (instrument panel J/B) is connected to the rear right door lock assembly via terminal LSWR (with smart entry and start system) or LSWP (without smart entry and start system), and rear right door lock/unlock state signals are input to the main body ECU (instrument panel J/B).
The main body ECU (instrument panel J/B) applies voltage to the door unlock detection switch via terminal LSWR (with smart entry and start system) or LSWP (without smart entry and start system). When the door unlock detection switch is on (there is continuity between the switch terminals), a lock state signal is input to the main body ECU (instrument panel J/B). When the switch is off (there is no continuity between the switch terminals), an unlock state signal is input.

WIRING DIAGRAM

B150881E02

INSPECTION PROCEDURE

HINT:
Start the inspection from step 1 if the vehicle is equipped with only the smart entry and start system, or if the vehicle is not equipped with the smart entry and start system, but is equipped with the theft deterrent system. Start from step 2 if the vehicle is equipped with neither the smart entry and start system nor the theft deterrent system.


1. READ VALUE ON INTELLIGENT TESTER

  1. E138501E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select RR-Door Lock Pos SW in the DATA LIST and read the tester display.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR-Door Lock Pos SW
    Rear right door lock position switch signal / ON or OFF
    ON: Rear right door lock is in UNLOCK position
    OFF: Rear right door lock is in LOCK position
    -

    OK:
    The display is as specified in the "Normal Condition" column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT REAR DOOR LOCK ASSEMBLY (UNLOCK DETECTION SWITCH)

  1. E123891E02
    Remove the rear door lock assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Measurement Condition
    Door Lock Condition
    Specified Condition
    6 - 9
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    10 kΩ or higher
    6 - 9
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock
    Below 1 Ω



NG
REPLACE REAR DOOR LOCK ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK - MAIN BODY ECU)

  1. Disconnect the main body ECU (instrument panel J/B) connector.B138095E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    with Smart Entry and Start System for RHD:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    J5-6 (LSSR) - E6-5 (LSWR)
    Always
    Below 1 Ω
    J5-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    J5-9 (E) - Body ground
    Always
    Below 1 Ω
    without Smart Entry and Start System for RHD:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    J5-6 (LSSR) - E6-27 (LSWP)
    Always
    Below 1 Ω
    J5-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    J5-9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL J/B)


← Rear Door UNLOCK Detection Switch LH Circuit (from Jun 2009)Rear Door UNLOCK Detection Switch RH Circuit (from Jun 2009) →