2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E188090E04

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver, steering pad switch, heater control switch or others (hazard switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result:
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on (radio receiver, hazard switch, heater control switch, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

  1. E182617E06
    Disconnect the spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E18-12 (IL+2) - Body ground
    Light control switch tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH
  1. Disconnect the steering pad switch connector.

  1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch connector.E129805E04

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch comes on.

    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch for 3 Spoke Type)
    *2
    Component without harness connected
    (Steering Pad Switch for 4 Spoke Type)



NG
REPLACE STEERING PAD SWITCH
OK


4. INSPECT SPIRAL CABLE

  1. E168547E11
    Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-5 (IL+2) - E18-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL CABLE
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)
  1. Disconnect the radio receiver and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-6 (SWG) - E18-4 (EAU)
    Always
    Below 1 Ω
    F8-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER)
  1. Disconnect the radio receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F6-10 (ILL+) - Body ground
    Light control switch tail or head
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND)
  1. Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-7 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE


← Illumination Circuit (Oct 2006 – May 2009)Speaker Circuit (Jun 2006 – May 2009) →