2006-2011 Camry Aurion · Service Manual RESTRAINTS

Front Passenger Side Seat Belt Warning Light Malfunction

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

only G.C.C. countries:
When the passenger seat belt is not fastened with the ignition switch on (IG) and the passenger seat occupied, check that the passenger seat belt warning light on the clock display blinks. The occupant detection sensor detects if the passenger seat is occupied and sends signals to the meter assembly. The inner belt detects the passenger seat belt condition and sends signals to the meter assembly. After receiving the signals from the occupant detection sensor and inner belt, the meter assembly sends signals to the clock assembly to request the passenger seat belt warning light to blink or go off.

WIRING DIAGRAM

B150533E04

INSPECTION PROCEDURE


1. CHECK WIRE HARNESS (BATTERY POSITIVE AND BODY GROUND)

  1. B137073E01
    Disconnect the clock assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F3-3 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE GAUGE NO. 1 FUSE, HARNESS OR CONNECTOR
OK


2. CHECK CLOCK ASSEMBLY

  1. B137074E01
    Disconnect the clock assembly connector.

  1. Apply battery voltage to the connector according to the table below.

    Standard:
    Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (IG)
    Battery negative (-) → Terminal 10 (PBEW), 19 (GND1)
    Comes on (Seat belt warning light)



NG
REPLACE CLOCK ASSEMBLY
OK


3. CHECK WIRE HARNESS (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

  1. B137077E03
    Disconnect the combination meter assembly and clock assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-16 (P/SB)*1 - F3-10 (PBEW)
    F1-9 (P/SB)*2 - F3-10 (PBEW)
    Always
    Below 1 Ω
    F1-16 (P/SB)*1 - Body ground
    F1-9 (P/SB)*2 - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. *1: for 2AZ-FE
    2. *2: for 2GR-FE



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION COVER)

  1. B081922E02
    Disconnect the occupant detection sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - A-3
    The passenger seat is occupied
    Below 100 Ω
    A-1 - A-3
    The passenger seat is not occupied
    Below 1 MΩ



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION COVER (OCCUPANT DETECTION SENSOR)
OK


5. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY)

  1. B150534E03
    Disconnect the combination meter assembly and front seat inner belt assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-19 (PBKL)*1 - O22-1
    F1-8 (PBKL)*2 - O22-1
    Always
    Below 1 Ω
    F1-19 (PBKL)*1 - Body ground
    F1-8 (PBKL)*2 - Body ground
    Always
    10 kΩ or higher
    O22-3 - Body ground
    Always
    Below 1 Ω

    HINT:
    1. *1: for 2AZ-FE
    2. *2: for 2GR-FE



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SIDE)
  1. Replace the front seat inner belt assembly (front passenger side)

OK:
Seat belt warning operation returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

END


← Front Passenger Side Seat Belt Warning Light Malfunction (Jun 2006 – Sep 2006)Front Passenger Side Seat Belt Warning Light Malfunction (from Jun 2009) →