2006-2011 Camry Aurion · Service Manual TRANSMISSION

P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

SYSTEM DESCRIPTION

The TCM uses the vehicle speed signal to determine the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect mechanical problems of the shift solenoid valves and valve body.
DTC No.
DTC Detection Condition
Trouble Area
P0746
The engine revs freely when 1st, 2nd, 3rd, or 4th gear is requested. (2-trip detection logic)
When either of the following is detected twice (2-trip detection logic):
  1. When 5th gear is requested, 4th gear is engaged.
  2. When 6th gear is requested, 4th gear is engaged.
  1. Shift solenoid valve SL1 remains open or closed
  2. Valve body (blocked)
  3. Automatic transaxle is clutch, brake or gear etc.

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the TCM detects the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear position). When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL.

INSPECTION PROCEDURE


1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0746)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester on.

  1. Enter the following items: "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    Only "P0746" is output
    A
    "P0746" and other DTCs are output
    B

    HINT:
    If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.



A
Go to step 3
B


2. PERFORM ACTIVE TEST USING SHIFT

NOTICE:
This test should always be performed by at least 2 people.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester on.

  1. Enter the following items: "Powertrain / ECT / Active Test / Control the Shift Position".

    HINT:
    Comparing the shift position commanded by the Active Test with the actual shift position enables confirmation of the problem (Click here).
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    [Test Details]
    Operate the shift solenoid valve and set each shift position by yourself.
    [Others]
    1. Press "←" button: Shift up
    2. Press "→" button: Shift down
    [Shift Position]
    0001: 1st / 0010: 2nd / 0011: 3rd / 0100: 4th / 0101: 5th / 0110: 6th
    Possible to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds. Doing so will damage the automatic transaxle.

    NOTICE:
    1. This test can be conducted when the vehicle is stopped.
    2. When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.

    HINT:
    The shift position commanded by the TCM is shown in the "Data List/Shift Status" display on the intelligent tester.

  1. Check the vehicle speed and the gear position when the engine speed is 1,000 rpm.

    HINT:
    Because the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.


    Standard:
    1st
    2nd
    3rd
    4th
    5th
    6th
    8 to 12 km/h (5 to 7.5 mph)
    15 to 19 km/h (9.3 to 11.8 mph)
    21 to 25 km/h (13.0 to 15.5 mph)
    31 to 35 km/h (19.3 to 21.7 mph)
    44 to 48 km/h (27.3 to 29.8 mph)
    52 to 56 km/h (32.3 to 34.8 mph)

  1. Compare the TCM gear shift command and the actual gear position.

    Result:
    Actuator gear position under malfunction
    TCM gear shift command
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    6th
    Shift solenoid SL1
    Stuck ON
    1st
    2nd
    3rd
    4th
    4th
    4th
    A
    Stuck OFF
    N*1
    N*1
    N*1
    N*1
    5th
    6th
    Shift solenoid SL2
    Stuck ON
    4th
    4th
    4th
    4th
    5th
    6th
    B
    Stuck OFF
    1st
    2nd
    3rd
    1st
    N*1
    N*1
    Shift solenoid SL3
    Stuck ON
    2nd
    2nd
    3rd
    4th
    5th
    6th
    C
    Stuck OFF
    1st
    1st
    3rd
    4th
    5th
    N*1
    Shift solenoid SL4
    Stuck ON*3
    3rd
    3rd
    3rd
    4th
    5th
    5th
    D
    Stuck OFF
    1st
    2nd
    1st
    4th
    N*1
    6th
    Shift solenoid SLT
    Stuck ON
    N*2
    N*2
    N*2
    N*2
    N*2
    N*2
    E
    Stuck OFF*3
    1st
    2nd
    3rd
    4th
    5th
    6th

    HINT:
    1. *1: Neutral
    2. *2: If the shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
    3. *3: When the shift solenoid SLT is stuck OFF, gear shifting is normal.



B
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL2) PERFORMANCE DTC P0776)

C
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL3) PERFORMANCE DTC P0796)

D
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL4) PERFORMANCE DTC P2808)

E
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SLT) PERFORMANCE DTC P2714)
A


3. INSPECT SHIFT SOLENOID VALVE (SL1)

  1. G020767E05
    Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    5.0 to 5.6 Ω
    (at 20°C (68°F))

  1. Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE (SL1)
OK


4. INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the valve body assembly (Click here).

OK:
There are no foreign objects on each valve and the valves operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


5. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

OK:
The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY
OK

REPLACE AUTOMATIC TRANSAXLE ASSEMBLY


← P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) (from Jun 2009)P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (from Jun 2009) →