Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009from Jun 2009
1.
DRAIN AUTOMATIC TRANSAXLE FLUID
Remove the refill plug and gasket.
Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.
Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube.
Drain the automatic transaxle fluid.
Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube.
Torque:
1.7 N*m{
17 kgf*cm
, 15 in.*lbf
}
Using a 6 mm socket hexagon wrench, install the overflow plug with a new gasket.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
Install the refill plug with a new gasket.
Torque:
49 N*m{
500 kgf*cm
, 36 ft.*lbf
}
2.
REMOVE FRONT WHEELS
3.
REMOVE FRONT AXLE HUB NUT LH
Using SST and a hammer, release the staked part of the front axle hub nut.
SST
09930-00010
NOTICE:
Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.
While applying the brakes, remove the front axle hub nut.
4.
REMOVE FRONT AXLE HUB NUT RH
HINT:
Use the same procedures as described for the LH side.
5.
SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
Remove the nut and separate the front stabilizer link assembly.
HINT:
If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.
6.
SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Use the same procedures as described for the LH side.
7.
SEPARATE FRONT SPEED SENSOR LH
Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.
Remove the bolt and separate the speed sensor from the steering knuckle.
NOTICE:
Prevent foreign matter from adhering to the speed sensor.
Be careful not to damage the speed sensor.
8.
SEPARATE FRONT SPEED SENSOR RH
HINT:
Use the same procedures as described for the LH side.
9.
SEPARATE TIE ROD END SUB-ASSEMBLY LH
Remove the cotter pin and nut.
Using SST, separate the tie rod end sub-assembly from the steering knuckle.
SST
09628-00011
NOTICE:
Make sure that the string of SST is securely tied to the vehicle.
Be careful not to damage the ball joint dust cover.
Be careful not to damage the steering knuckle.
Be careful not to damage the front disc brake dust cover.
10.
SEPARATE TIE ROD END SUB-ASSEMBLY RH
HINT:
Use the same procedures as described for the LH side.
11.
SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH
Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.
12.
SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH
HINT:
Use the same procedures as described for the LH side.
13.
SEPARATE FRONT AXLE ASSEMBLY LH
Put matchmarks on the front drive shaft assembly and the axle hub.
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
NOTICE:
Be careful not to damage the drive shaft boot and speed sensor rotor.
14.
SEPARATE FRONT AXLE ASSEMBLY RH
HINT:
Use the same procedures as described for the LH side.
15.
REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
Using SST, remove the front drive shaft assembly LH.
SST
09520-01010 09520-24010
(09520-32040)
NOTICE:
Be careful not to damage the drive shaft dust cover, boot, and oil seal.
Be careful not to drop the drive shaft assembly.
16.
REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
Using a screwdriver, remove the bearing bracket hole snap ring.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
NOTICE:
Do not damage the boot and oil seal.
17.
SECURE FRONT AXLE HUB SUB-ASSEMBLY
Secure the front axle hub bearing.
SST
09608-16042
(09608-02021, 09608-02041)
NOTICE:
The hub bearing may be damaged if it is subjected to the vehicle's full weight, such as moving the vehicle with the drive shaft removed. If it is necessary to place the vehicle's weight on the hub bearing, first support it with SST.
18.
REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL
Using SST, remove the oil seal from the transaxle case.
SST
09308-00010
19.
REMOVE TRANSAXLE HOUSING OIL SEAL
Using SST, remove the oil seal from the transaxle housing.