2006-2011 Camry Aurion · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Jun 2006


1. INSTALL FRONT DIFFERENTIAL SIDE GEAR

  1. C134915E01
    Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.


2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

  1. C134914E02
    Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


3. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

  1. C134918
    Using a pin punch and hammer, install the pinion shaft straight pin.

  1. C134919
    Using a chisel and hammer, stake the differential case.

    NOTICE:
    Stake it after adjusting the backlash.


4. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. C134920E01
    Using SST and a press, install the front differential case front tapered roller bearing to the differential case.
    SST
    09710-30012   (09710-04081)
    09550-60010   (09951-00480)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during installation of the bearing inner race.

  1. C083736
    Using SST and a hammer, install the front differential case front tapered roller bearing outer race to the transaxle housing.
    SST
    09950-60020   (09951-00750)
    09950-70010   (09951-07200)


5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

  1. C134921E01
    Using SST and a press, install the front differential case rear tapered roller bearing to the differential case.
    SST
    09710-30012   (09710-04081)
    09550-60010   (09951-00480)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during installation of the bearing inner race.

  1. D026449E01
    Using SST and a hammer, install the front differential case rear tapered roller bearing outer race to the transaxle housing.
    SST
    09550-60010   (09951-00790)
    09950-70010   (09951-00710)

    NOTICE:
    Clearance is not allowed between the bearing and transaxle housing.


6. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

  1. C134922
    Install the differential assembly to the transaxle case.

  1. C147840E01
    Clean the matching surfaces of the transaxle case and transaxle housing.

  1. Install the transaxle housing to the transaxle case and tighten them with the 18 bolts.

    Torque:
    Bolt A:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }
    Bolt B,C:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    Bolt D:
    10 N*m{ 101 kgf*cm , 7 ft.*lbf }

    Bolt length:
    Bolt A,B,D:
    50 mm (1.969 in.)
    Bolt C:
    42 mm (1.654 in.)

  1. D025604E01
    Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.
    SST
    09564-32011  

  1. Using SST and a torque wrench, measure the turning torque of the differential.

    SST
    09564-32011  

    Turning torque at 60 rpm:
    New bearing:
    0.20 to 0.69 N*m (2.0 to 7.0 kgf*cm, 1.8 to 6.1 in.*lbf)
    Used bearing:
    0.10 to 0.35 N*m (1.0 to 3.6 kgf*cm, 0.9 to 3.1 in.*lbf)

    HINT:
    If the turning torque is not within the specified range, refer to the table below to select a thrust washer so that the turning torque is within the specified range.

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    0
    1.90 (0.0748)
    A
    2.40 (0.0945)
    1
    1.95 (0.0768)
    B
    2.45 (0.0965)
    2
    2.00 (0.0787)
    C
    2.50 (0.0984)
    3
    2.05 (0.0807)
    D
    2.55 (0.1004)
    4
    2.10 (0.0827)
    E
    2.60 (0.1024)
    5
    2.15 (0.0846)
    F
    2.65 (0.1043)
    6
    2.20 (0.0866)
    G
    2.70 (0.1063)
    7
    2.25 (0.0886)
    H
    2.75 (0.1083)
    8
    2.30 (0.0906)
    J
    2.80 (0.1102)
    9
    2.35 (0.0925)
    -
    -

  1. C147840
    Remove the 18 bolts and the transaxle housing.

  1. C134922
    Remove the differential assembly.


7. INSTALL FRONT DIFFERENTIAL RING GEAR

  1. D025215E04
    Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

    NOTICE:
    Do not overheat the ring gear over 110°C (230.0°F).

  1. Clean the contact surface of the front differential case.

  1. C134908E06
    Align the matchmarks, and install the front differential ring gear case quickly.

    NOTICE:
    Do not install the bolts while the ring gear is hot.

  1. C134909E01
    Tighten the 10 bolts.

    Torque:
    95 N*m{ 970 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in a diagonal pattern.


8. INSTALL TRANSAXLE HOUSING OIL SEAL

  1. D026451E01
    Using SST and a hammer, install a new oil seal.
    SST
    09608-32010  
    09950-70010   (09951-07150)

  1. Coat the lip of the oil seal with a small amount of MP grease.

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


9. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

  1. C134923E01
    Using SST and a hammer, install a new oil seal.
    SST
    09726-36010  
    09950-70010   (09951-07150)

  1. Coat the lip of the oil seal with a small amount of MP grease.

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

← INSPECTION (from Jun 2006)INSTALLATION (from Jun 2006) →