Remove the 2 bolts and disconnect the 2 engine wires.
Remove the 8 bolts, 2 nuts, and the cylinder head cover.
10.
SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.
Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as above.
NOTICE:
Make sure that the timing mark of the No.2 bearing cap is aligned with the timing mark as the Type B camshaft sprocket has several other marks.
11.
CHECK VALVE CLEARANCE
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Standard valve clearance (cold):
Item
Standard Condition
Intake
0.19 to 0.29 mm (0.0075 to 0.0114 in.)
Exhaust
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to TDC/compression.
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Standard valve clearance (cold):
Item
Standard Condition
Intake
0.19 to 0.29 mm (0.0075 to 0.0114 in.)
Exhaust
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
Measured used lifter thickness = 5.250 mm (0.2067 in.)
New lifter thickness = 5.410 mm (0.2130 in.) (Excess clearance + Used lifter thickness = Ideal new lifter)
0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
Closest new lifter = 5.420 mm (0.2134 in.)
Select No. 42 lifter
Select a new lifter with a thickness as close as possible to the calculated values.
HINT:
Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).
The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.))
Valve lifter selection chart (intake).
New lifter thickness
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
06
5.060 (0.1992)
30
5.300 (0.2087)
54
5.540 (0.2181)
08
5.080 (0.2000)
32
5.320 (0.2094)
56
5.560 (0.2189)
10
5.100 (0.2008)
34
5.340 (0.2102)
58
5.580 (0.2197)
12
5.120 (0.2016)
36
5.360 (0.2110)
60
5.600 (0.2205)
14
5.140 (0.2024)
38
5.380 (0.2118)
62
5.620 (0.2213)
16
5.160 (0.2031)
40
5.400 (0.2126)
64
5.640 (0.2220)
18
5.180 (0.2039)
42
5.420 (0.2134)
66
5.660 (0.2228)
20
5.200 (0.2047)
44
5.440 (0.2142)
68
5.680 (0.2236)
22
5.220 (0.2055)
46
5.460 (0.2150)
70
5.700 (0.2244)
24
5.240 (0.2063)
48
5.480 (0.2157)
72
5.720 (0.2252)
26
5.260 (0.2071)
50
5.500 (0.2165)
74
5.740 (0.2260)
28
5.280 (0.2079)
52
5.520 (0.2173)
-
-
Standard intake valve clearance (cold):
0.19 to 0.29 mm (0.0075 to 0.0114 in.)
EXAMPLE: The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.
Valve lifter selection chart (exhaust).
New lifter thickness
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
06
5.060 (0.1992)
30
5.300 (0.2087)
54
5.540 (0.2181)
08
5.080 (0.2000)
32
5.320 (0.2094)
56
5.560 (0.2189)
10
5.100 (0.2008)
34
5.340 (0.2102)
58
5.580 (0.2197)
12
5.120 (0.2016)
36
5.360 (0.2110)
60
5.600 (0.2205)
14
5.140 (0.2024)
38
5.380 (0.2118)
62
5.620 (0.2213)
16
5.160 (0.2031)
40
5.400 (0.2126)
64
5.640 (0.2220)
18
5.180 (0.2039)
42
5.420 (0.2134)
66
5.660 (0.2228)
20
5.200 (0.2047)
44
5.440 (0.2142)
68
5.680 (0.2236)
22
5.220 (0.2055)
46
5.460 (0.2150)
70
5.700 (0.2244)
24
5.240 (0.2063)
48
5.480 (0.2157)
72
5.720 (0.2252)
26
5.260 (0.2071)
50
5.500 (0.2165)
74
5.740 (0.2260)
28
5.280 (0.2079)
52
5.520 (0.2173)
-
-
Standard exhaust valve clearance (cold):
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
EXAMPLE: The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.
Install the selected valve lifter.
13.
INSTALL CAMSHAFT
Apply a light coat of engine oil to the journal portion of the camshaft.
Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark on the camshaft timing gear as shown in the illustration.
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
No. 1 bearing cap:
30 N*m{
301 kgf*cm
, 22 ft.*lbf
}
No. 3 bearing cap:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
14.
INSTALL NO. 2 CAMSHAFT
Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.
Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.
NOTICE:
Make sure that the paint mark of the chain is aligned with the timing mark as the Type B camshaft sprocket has several other marks.
While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
No. 2 bearing cap:
30 N*m{
301 kgf*cm
, 22 ft.*lbf
}
No. 3 bearing cap:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.
Torque:
54 N*m{
551 kgf*cm
, 40 ft.*lbf
}
NOTICE:
Be careful not to damage the valve lifter.
Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.
NOTICE:
Make sure that the paint mark of the chain is aligned with the timing mark as the Type B camshaft sprocket has several other marks.
15.
INSTALL NO. 1 CHAIN TENSIONER
Release the ratchet pawl, then fully push in the plunger and put the hook to the pin so that the plunger is in the position shown in the illustration.
Install a new gasket and the chain tensioner with the 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
NOTICE:
If the hook releases the plunger while the chain tensioner is being installed, set the hook again.
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
Turn the crankshaft clockwise, then check that the plunger is extended.
16.
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Apply seal packing to the 2 locations shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the cylinder head cover.
Install the cylinder head cover with the 8 bolts and 2 nuts.