REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
- HINT:
- Use the same procedures for the RHD and LHD.
- The procedures listed below are for the LHD.
| 1.
PRECAUTION |
 |
Click here.
| 2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
|
| 3.
DRAIN BRAKE FLUID
|
 |
- NOTICE:
- Stop the engine and depress the brake pedal several times until no vacuum is left in the brake booster.
- If the brake fluid leaks onto any painted surface, wash off and remove the brake fluid completely.
| 4.
REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for LHD)
|
 |
- Disconnect the mass air flow meter connector (*1).
Disconnect the purge VSV connector (*2).
Disconnect the 2 purge VSV vacuum hoses (*3).
Disconnect the purge line hose from the clamp (*4).
- Disconnect the No. 2 ventilation hose from the air cleaner hose.
- Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.
- Remove the 2 bolts and air cleaner cap.
Remove the air cleaner filter element from the air cleaner case.
| 5.
REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for LHD)
|
 |
- Disconnect the hose clamp.
Remove the 3 bolts and air cleaner case.
| 6.
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
|
 |
- Disconnect the connector.
- Remove the 4 bolts and the windshield wiper motor and link assembly.
| 7.
REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY
|
 |
- Disengage the clamp.
Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.
| 8.
REMOVE BRAKE BOOSTER ASSEMBLY (for LHD) |
 |
Click here.
| 9.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 10.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 11.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
|
 |
- Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.
| 12.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
|
 |
- Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the No. 1 instrument panel sub-assembly.
| 13.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
|
 |
- Disengage the 3 claws and the 2 clips.
Disconnect the connector and remove the No. 1 instrument panel sub-assembly.
| 14.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL
|
 |
- Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
| 15.
REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
|
 |
- Remove the 2 clips.
Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.
| 16.
REMOVE COMBINATION METER ASSEMBLY
|
 |
- Remove the 4 screws <E>.
Disconnect each connector and remove the combination meter assembly.
| 17.
DISCONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS |
 |
- Remove the clip and pin, and disconnect the push rod clevis from the clutch pedal.
| 18.
DISCONNECT CLUTCH RESERVOIR TUBE |
 |
- Using pliers, grip the claws of the clip and slide the clip to disconnect the tube from the clutch master cylinder.
- HINT:
- Use a container to catch the fluid.
| 19.
DISCONNECT CLUTCH LINE |
 |
- Using SST, disconnect the clutch line.
- SST
- 09023-00101
- HINT:
- Use a container to catch the fluid.
| 20.
REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for LHD) |
 |
- Remove the 2 nuts and clutch master cylinder.
Remove the gasket from the clutch master cylinder assembly.
| 21.
REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for RHD) |
 |
- Remove the 2 nuts and clutch master cylinder.
Remove the gasket from the clutch master cylinder assembly.