2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL BLOWER ASSEMBLY

  1. E129997
    Install the blower assembly with the 6 screws.

  1. E129996
    Connect the connector.


2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

  1. Install the conditioner unit assembly to the instrument panel reinforcement assembly with the 2 screws and 3 bolts.

    E128522E01

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    Tighten the bolts and screws in the order shown in the illustration to install the air conditioner unit assembly.

  1. Driver side:

    1. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.

      E129156E04

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Passenger side:

    1. Using a 12 mm hexagon wrench, adjust the position of the 2 collars.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the instrument panel reinforcement assembly with the 2 bolts and nut.

    E128520

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } (NUT)

  1. Install the 2 bolts and 2 caps.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }

  1. Connect the connectors and clamps.

  1. Install the 6 nuts and 7 bolts.

    E136484E01


3. INSTALL STEERING COLUMN ASSEMBLY

  1. C145844E01
    Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.


4. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C132549E01
    Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. C132548E02
    Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. C133172
    Install the clamp to the steering column hole shield.


5. INSTALL NO. 1 AIR DUCT

  1. C132547E02
    Engage the 2 claws to install the No. 1 air duct.


6. INSTALL REAR NO. 1 AIR DUCT

  1. E135676
    Engage the 2 claws to install the rear No. 1 air duct.


7. INSTALL REAR NO. 2 AIR DUCT

  1. E135675
    Engage the 2 claws to install the rear No. 2 air duct.


8. INSTALL FLOOR CARPET BRACKET RH

9. INSTALL FLOOR CARPET BRACKET LH

10. INSTALL NO. 1 CONSOLE BOX DUCT

  1. C129716
    Install the No. 1 console box duct with the clip.


11. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <H> and 2 nuts <I>.

    B134014E06

  1. Engage each clamp.

  1. Install the bolt <J>.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the 2 passenger airbag bolts <C>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect each connector and install the instrument panel safety pad assembly.

    B134013E01


12. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C132564E01
    Connect the connector (yellow colored one).


13. INSTALL NO. 1 DEFROSTER NOZZLE GARNISH

  1. B134011E01
    Connect each connector.

  1. Engage the 4 guides.

  1. Engage the 8 clips and install the No. 1 defroster nozzle garnish.


14. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH (for 6 Speakers)
  1. Connect the connector.

  1. E129167
    Install the front No. 2 speaker assembly with the 2 bolts.


15. INSTALL INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY

  1. B134009E01
    Engage the 2 guides.

  1. Engage the 6 claws and the 2 clips to install the instrument panel No. 1 speaker panel sub-assembly.


16. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY

  1. B134007
    Engage the 4 clips and install the instrument panel No. 1 register assembly.


17. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


18. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

  1. B154714E01
    Remove the protective cover.

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


19. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH (for 6 Speakers)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


20. INSTALL INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY

  1. B134010E01
    Engage the 2 guides.

  1. Engage the 6 claws and the 2 clips to install the instrument panel No. 2 speaker panel sub-assembly.


21. INSTALL INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY

  1. B134008
    Engage the 4 clips and install the instrument panel No. 3 register assembly.


22. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


23. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

  1. B154715E01
    Remove the protective cover.

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


24. INSTALL NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Engage the clip.

  1. Install the No. 1 console box insert front with the 3 screws <F>.


25. INSTALL NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Engage the clip.

  1. Install the No. 2 console box insert front with the 3 screws <F>.


26. INSTALL CONSOLE BOX ASSEMBLY

  1. B134002E01
    Install the 2 screws <F>.

  1. B149935E03
    Install the console box assembly with the 2 bolts <G>.

  1. Engage the clamp.


27. INSTALL CONSOLE BOX CARPET

  1. B134004
    Install the console box carpet.


28. INSTALL CONSOLE BOX POCKET
  1. Install the console box pocket.


29. INSTALL RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player)

  1. E135568
    Connect each connector.

  1. Engage the 6 clips.

  1. Install the radio and cassette tape with heater control panel assembly with the 4 bolts.


30. INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player)

  1. E129175
    Connect each connector.

  1. Engage the 4 clips.

  1. Install the radio receiver with heater control panel assembly with the 4 bolts.


31. INSTALL NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)
  1. Connect each connector.

  1. E137564
    Engage the 4 clips.

  1. Install the navigation receiver with heater control panel assembly with the 4 bolts.


32. INSTALL INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY
  1. Connect the connector.

  1. B152785
    Engage the 7 clips and install the instrument panel No. 2 register assembly.


33. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
  1. Connect each connector.

  1. B141243E01
    Engage the 2 claws and 2 clips.

  1. Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.


34. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B149934
    Connect the connector.

  1. Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.


35. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B144604
    Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.


36. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B144604
    Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.


37. INSTALL POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)

  1. B148447
    Engage the 6 claws and the 3 clips to install the position indicator housing assembly.


38. INSTALL POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)

  1. B152778
    Engage the 2 claws and the 5 clips to install the position indicator housing assembly as shown in the illustration.


39. INSTALL UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B145877
    Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.


40. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144605
    Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.


41. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144599
    Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.


42. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B148448
    Install the shift lever knob sub-assembly.


43. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B152780
    Install the shift lever knob sub-assembly.


44. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B152775
    Install the shift lever knob sub-assembly.


45. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B133992E01
    Engage the 3 claws and 3 clips.

  1. Install the 4 screws <B>.

  1. Install the lower instrument panel sub-assembly with the bolt <A>.


46. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133989E01
    Engage the 4 claws and 2 guides, and install the instrument panel No. 2 under cover sub-assembly.


47. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


48. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


49. INSTALL COMBINATION METER ASSEMBLY

  1. B152781E01
    Connect each connector.

  1. Install the combination meter assembly with the 4 screws <E>.


50. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel sub-assembly with the 2 clips.


51. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B144612
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


52. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)

  1. B159330
    Connect the connector.

  1. Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


53. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
  1. Connect each connector.

  1. B149938
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


54. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
  1. Connect each connector.

  1. B149936
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


55. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. C145843
    Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


56. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C107193
    Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

  1. C107194E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


57. INSTALL STEERING COLUMN COVER

  1. B137294E01
    Engage the claw and install the upper steering column cover.

  1. Engage the 2 claws and install the lower steering column cover.

  1. Install the steering column cover with the 2 screws <D>.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


58. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.


59. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


60. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


61. INSTALL STEERING WHEEL ASSEMBLY

  1. C145840E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


62. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133859E01
    Support the steering pad with one hand.

  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C146015E01
    Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


63. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. Engage the claw and install the No. 3 lower steering wheel cover.

    C146016E01


64. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. Engage the claw and install the No. 2 lower steering wheel cover.

    C146017E01


65. INSTALL HEATER WATER HOSE INLET

  1. E128511
    Install the water hose and attach the clip.


66. INSTALL HEATER WATER HOSE OUTLET
  1. Use the same procedures described for the heater inlet water hose.


67. INSTALL AIR CONDITIONING TUBE AND ACCESSORY
  1. Remove the attached vinyl tape from the tube.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the air conditioning tube and accessory.

  1. Install the air conditioner tube and accessory.


68. INSTALL SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the suction hose sub-assembly.

  1. E129157
    Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


69. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.

    Torque:
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


70. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E135590E01
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.

  1. E135589
    Connect the connector.


71. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E135588
    Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


72. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Engage the claw and install the front fender to cowl side seal RH.


73. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Engage the claw and install the front fender to cowl side seal LH.


74. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128820E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)


75. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128821E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


76. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for LHD)

77. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for LHD)
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


78. CONNECT NEGATIVE BATTERY TERMINAL

79. INSPECT STEERING PAD

  1. C146010E01
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


80. INSPECT SRS WARNING LIGHT
(Click here)

81. ADD ENGINE COOLANT (for 2AZ-FE)
  1. Close the radiator drain cock plug and cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.7 liters (7.1 US qts, 5.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


82. ADD ENGINE COOLANT (for 2GR-FE)
  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    9.0 liters (9.5 US qts, 7.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


83. INSPECT FOR COOLANT LEAK (for 2AZ-FE)

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A135234
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


84. INSPECT FOR COOLANT LEAK (for 2GR-FE)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

  1. A133894
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


85. CHARGE WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.

  1. Charge with refrigerant HFC-134a (R134a).

    I037365E09

    Standard:
    450 to 550 g (15.9 to 19.4 oz.)

    SST
    07110-58060   (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

    NOTICE:
    1. Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear.
      The refrigerant amount should be checked by quantity, not with the sight glass.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from the A/C system.


86. WARM UP ENGINE
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


87. INSPECT FOR REFRIGERANT LEAK
  1. After recharging with refrigerant gas, inspect for refrigerant gas leak using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. IG OFF
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E20
    Using a gas leak detector, inspect for refrigerant line leaks.

  1. N014519E06
    Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.

  1. If a gas leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.

← REASSEMBLY (from Oct 2006)INSTALLATION (from Jun 2009) →