INSTALLATION
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Install the conditioner unit assembly to the instrument panel reinforcement assembly with the 2 screws and 3 bolts.


- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
- NOTICE:
- Tighten the bolts and screws in the order shown in the illustration to install the air conditioner unit assembly.
Driver side:
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.


- Torque:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
Passenger side:
Using a 12 mm hexagon wrench, adjust the position of the 2 collars.
- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Install the instrument panel reinforcement assembly with the 2 bolts and nut.


- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf } (NUT)
Install the 2 bolts and 2 caps.
- Torque:
- 17 N*m{ 175 kgf*cm , 13 ft.*lbf }
Connect the connectors and clamps.
Install the 7 nuts and 5 bolts.


| 2. INSTALL STEERING COLUMN ASSEMBLY |
Install the steering column assembly with the bolt and 2 nuts.

- Torque:
- 21 N*m{ 214 kgf*cm , 16 ft.*lbf }
Connect the connectors and engage the wire harness clamps to the steering column assembly.
| 3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

Install the bolt.

- Torque:
- 35 N*m{ 360 kgf*cm , 26 ft.*lbf }
Install the clamp to the steering column hole shield.

| 4. INSTALL NO. 1 AIR DUCT |
Engage the 2 claws to install the No. 1 air duct.

| 5. INSTALL REAR NO. 1 AIR DUCT |
Engage the 2 claws to install the rear No. 1 air duct.

| 6. INSTALL REAR NO. 2 AIR DUCT |
Engage the 2 claws to install the rear No. 2 air duct.

| 7. INSTALL FLOOR CARPET BRACKET RH |
| 8. INSTALL FLOOR CARPET BRACKET LH |
| 9. INSTALL NO. 1 CONSOLE BOX DUCT |
Install the No. 1 console box duct with the clip.

| 10. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Engage the 5 claws.
- NOTICE:
- Do not allow the wire harness to get caught in the claws.
Install the 2 bolts <J> and 2 nuts <L>.


Engage each clamp.
Install the bolt <E>.
- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
Install the 2 passenger airbag bolts <M>.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Connect each connector and install the instrument panel safety pad assembly.


| 11. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY |
Connect the connector (yellow colored one).

| 12. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
Connect the connector.
Install the front No. 2 speaker assembly with the 2 bolts.

| 13. INSTALL INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY |
Engage the 2 guides.

Engage the 6 claws and the 2 clips to install the instrument panel No. 1 speaker panel sub-assembly.
| 14. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY |
Engage the 4 clips and install the instrument panel No. 1 register assembly.

| 15. INSTALL FRONT PILLAR GARNISH LH |
Remove the protective cover.

Install a new clip <A> on the front pillar garnish LH.

Engage the 2 claws and 2 clips, then install the front pillar garnish LH.
| 16. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here)
| 17. INSTALL INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY |
Engage the 2 guides.

Engage the 6 claws and the 2 clips to install the instrument panel No. 2 speaker panel sub-assembly.
| 18. INSTALL INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY |
Engage the 4 clips and install the instrument panel No. 3 register assembly.

| 19. INSTALL FRONT PILLAR GARNISH RH |
Remove the protective cover.

Install a new clip <A> on the front pillar garnish RH.

Engage the 2 claws and 2 clips, then install the front pillar garnish RH.
| 20. INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (for Radio Receiver Type) |
Connect each connector.

Engage the 4 clips.
Install the radio receiver with heater control panel assembly with the 4 bolts.
| 21. INSTALL RADIO AND DISPLAY WITH HEATER CONTROL PANEL ASSEMBLY (for Radio and Display Type) |
Connect each connector.

Engage the 6 clips.
Install the radio and display with heater control panel assembly with the 4 bolts.
| 22. INSTALL NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System) |
Connect each connector.
Engage the 4 clips.

Install the navigation receiver with heater control panel assembly with the 4 bolts.
| 23. INSTALL CONSOLE BOX ASSEMBLY |
Engage the 2 claws.

Install the 2 bolts <I>.

Install the 3 screws <H>.

Install the console box assembly with the 3 screws <H>.

Engage the clamp.

| 24. INSTALL CONSOLE BOX CARPET |
Install the console box carpet.

| 25. INSTALL INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY |
Connect each connector.
Engage the 11 claws and install the instrument panel No. 2 register assembly.

| 26. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Connect the connector.
Engage the 10 claws and install the upper console panel sub-assembly.

| 27. INSTALL UPPER CONSOLE PANEL FRONT GARNISH |
Connect each connector.

Engage the 6 claws and install the upper console panel front garnish.
| 28. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
Install the shift lever knob sub-assembly.

| 29. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Engage the 3 claws and 3 clips.

Install the screw <F> or <N>.
Install the 3 screws <F>.
Install the lower instrument panel sub-assembly with the bolt <D>.
| 30. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover sub-assembly.

| 31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
Engage the 2 clips.

Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 32. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

| 33. INSTALL COMBINATION METER ASSEMBLY |
Connect each connector.

Install the combination meter assembly with the 4 screws <B>, <C> or <H>.
| 34. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
Engage the guide and the 4 claws.

Install the instrument cluster finish panel sub-assembly with the 2 clips.
| 35. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System) |
Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.

| 36. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System) |
Connect the connector.
Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.

| 37. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.

| 38. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 39. ADJUST SPIRAL CABLE SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

- NOTICE:
- Do not turn the spiral cable by the airbag wire harness.
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

- NOTICE:
- Do not turn the spiral cable by the airbag wire harness.
- HINT:
- The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
| 40. INSTALL STEERING COLUMN COVER |
Engage the claw <a> and install the upper steering column cover.

Engage the 2 claws <b> and install the lower steering column cover.
Install the steering column cover with the 2 screws <A>.
- Torque:
- 2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
| 41. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Install the air hose and connect each connector.

Engage the claw and the 4 clips.
Engage the 2 claws and the DLC3.
Install the lower No. 1 instrument panel finish panel with the screw <F> and bolt <D>.
| 42. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 43. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 44. INSTALL STEERING WHEEL ASSEMBLY |
Align the matchmarks on the steering wheel assembly and steering main shaft.

Install the steering wheel assembly set nut.
- Torque:
- 50 N*m{ 510 kgf*cm , 37 ft.*lbf }
Connect the connectors to the spiral cable sub-assembly.
| 45. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Support the steering pad with one hand.

Connect the 2 airbag connectors to the steering pad.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

- Torque:
- 8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
| 46. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
Engage the claw and install the No. 3 lower steering wheel cover.


| 47. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
Engage the claw and install the No. 2 lower steering wheel cover.


| 48. INSTALL HEATER WATER HOSE INLET |
Install the water hose and attach the clip.

| 49. INSTALL HEATER WATER HOSE OUTLET |
Use the same procedures described for the heater inlet water hose.
| 50. INSTALL AIR CONDITIONING TUBE AND ACCESSORY |
Remove the attached vinyl tape from the tube.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube assembly.
- Compressor oil:
- ND-OIL 8 or equivalent
Install the O-ring on the air conditioning tube and accessory.
Install the air conditioner tube and accessory.
| 51. INSTALL SUCTION HOSE SUB-ASSEMBLY |
Remove the attached vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.
- Compressor oil:
- ND-OIL 8 or equivalent
Install the O-ring on the suction hose sub-assembly.
Move the hook connector in the direction indicated by the arrow in the illustration.

Insert the pipe joint into the fitting hole securely and tighten the bolt.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
| 52. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY |
Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.

- Torque:
- Nut:
- 85 N*m{ 867 kgf*cm , 63 ft.*lbf }
- Bolt:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
| 53. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
Install the windshield wiper motor and link assembly with the 4 bolts.

- Torque:
- 7.5 N*m{ 77 kgf*cm , 66 in.*lbf }
- NOTICE:
- Tighten the bolts in the order shown in the illustration.
Connect the connector.

| 54. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

Install the 2 clips.
| 55. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
Engage the claw and install the front fender to cowl side seal RH.

| 56. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
Engage the claw and install the front fender to cowl side seal LH.

| 57. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
Clean the wiper arm serrations.

When reinstalling:
Clean the wiper pivot serrations with a wire brush.
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
- HINT:
- Hold the arm hinge by hand to fasten the nut.
Area
Measurement
A
37 to 52 mm (1.46 to 2.05 in.)
| 58. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
Clean the wiper arm serrations.

When reinstalling:
Clean the wiper pivot serrations with a wire brush.
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
- HINT:
- Hold the arm hinge by hand to fasten the nut.
Area
Measurement
A
23 to 38 mm (0.90 to 1.49 in.)
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 59. CONNECT NEGATIVE BATTERY TERMINAL |
| 60. INSPECT STEERING PAD |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

- Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
- Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
Make sure that the horn sounds.
- HINT:
- If the horn does not sound, inspect the horn system (Click here).
| 61. INSPECT SRS WARNING LIGHT |
| 62. ADD ENGINE COOLANT |
Close the radiator drain cock plug and 2 cylinder block drain cock plugs.
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
- Specified capacity:
- 9.0 liters (9.5 US qts, 7.9 lmp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Contact your TOYOTA dealer for further details.
- Contact your TOYOTA dealer for further details.
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reservoir tank cap.
Start the engine, and warm it up.
- HINT:
- Adjust the air conditioner set temperature to MAX (HOT).
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 63. INSPECT FOR COOLANT LEAK |
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
- NOTICE:
- Before performing each inspection, turn the A/C switch OFF.
Fill the radiator with coolant and attach a radiator cap tester.

Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 64. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).


- Standard:
- 450 to 550 g (15.9 to 19.4 oz.)
- SST
- 07110-58060
(07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)
- NOTICE:
- Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
- Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear.
The refrigerant amount should be checked by quantity, not with the sight glass.
- Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
- HINT:
- Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from the A/C system.
| 65. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
- NOTICE:
- Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.
| 66. INSPECT FOR REFRIGERANT LEAK |
After recharging with refrigerant gas, inspect for refrigerant gas leak using a halogen leak detector.
Carry out the test under the following conditions:
- IG OFF
- Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
- Repeat the test 2 or 3 times.
- Make sure that there is some refrigerant remaining in the refrigeration system.
When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)
- IG OFF
Using a gas leak detector, inspect for refrigerant line leaks.

Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.

- HINT:
- After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
- Bring the gas leak detector sensor under the drain hose.
- When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.
- After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
If a gas leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.
