Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009from Jun 2009
1.
RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
Start up the engine.
Turn the A/C switch on.
Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
2.
TURN FRONT WHEELS STRAIGHT AHEAD
3.
DISCONNECT BATTERY NEGATIVE TERMINAL
NOTICE:
Wait for 90 seconds after disconnecting the terminal to prevent the airbag from deploying. (Click here)
4.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
Remove the nut and the front wiper arm and blade assembly LH.
5.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
Remove the nut and the front wiper arm and blade assembly RH.
6.
REMOVE FRONT FENDER TO COWL SIDE SEAL LH
Disengage the claw and remove the front fender to cowl side seal LH.
7.
REMOVE FRONT FENDER TO COWL SIDE SEAL RH
Disengage the claw and remove the front fender to cowl side seal RH.
8.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Remove the 2 clips.
Disengage the 3 claws and remove the cowl top ventilator louver sub-assembly.
9.
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Disconnect the connector.
Remove the 4 bolts and the windshield wiper motor and link assembly.
10.
REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY
Disengage the clamp.
Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.
11.
DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt, and slide the hook connector.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction hose sub-assembly.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
12.
DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY
Disconnect the air conditioning tube and accessory.
Remove the O-ring from the air conditioner tube and accessory.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
13.
DISCONNECT HEATER WATER HOSE OUTLET
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.
NOTICE:
Do not apply excessive force to the heater outlet water hose.
Prepare a drain pan or cloth in case the coolant leaks.
14.
DISCONNECT HEATER WATER HOSE INLET
HINT:
Disconnection procedure for the heater inlet water hose is the same as that for the heater outlet water hose.
15.
REMOVE LOWER NO. 3 STEERING WHEEL COVER
Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.
HINT:
Tape up the screwdriver tip before use.
16.
REMOVE LOWER NO. 2 STEERING WHEEL COVER
Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.
HINT:
Tape up the screwdriver tip before use.
17.
REMOVE STEERING PAD
Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.
Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.
NOTICE:
When removing the steering pad, do not pull the airbag wire harness.
Disconnect the horn connector from the steering pad.
Disconnect the 2 airbag connectors and remove the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
18.
REMOVE STEERING WHEEL ASSEMBLY
Remove the steering wheel assembly set nut.
Put matchmarks on the steering wheel assembly and the steering main shaft.
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 6 claws as shown in the illustration.
Using a moulding remover, disengage the 5 claws as shown in the illustration.
Disconnect each connector and remove the instrument panel No. 2 register assembly.
37.
REMOVE CONSOLE BOX CARPET
Remove the console box carpet.
38.
REMOVE CONSOLE BOX ASSEMBLY
Disengage the clamp.
Remove the 3 screws <H>.
Remove the 3 screws <H>.
Remove the 2 bolts <I>.
Disengage the 2 claws and remove the console box assembly.
39.
REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (for Radio Receiver Type)
Remove the 4 bolts.
Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver with heater control panel assembly.
40.
REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)
Remove the 4 bolts.
Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver with heater control panel assembly.
41.
REMOVE FRONT PILLAR GARNISH LH
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.
44.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
Remove the 2 bolts and front No. 2 speaker assembly.
Disconnect the connector.
45.
REMOVE FRONT PILLAR GARNISH RH
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.