2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


2. TURN FRONT WHEELS STRAIGHT AHEAD

3. DISCONNECT BATTERY NEGATIVE TERMINAL

NOTICE:
Wait for 90 seconds after disconnecting the terminal to prevent the airbag from deploying. (Click here)


4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for LHD)

  1. A144946E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).

  1. A146036
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. A135668
    Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A146037
    Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


5. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for LHD)

6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E135586
    Remove the nut and the front wiper arm and blade assembly LH.


7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E135587
    Remove the nut and the front wiper arm and blade assembly RH.


8. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Disengage the claw and remove the front fender to cowl side seal LH.


9. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Disengage the claw and remove the front fender to cowl side seal RH.


10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E135588
    Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.


11. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E135589
    Disconnect the connector.

  1. E135590
    Remove the 4 bolts and the windshield wiper motor and link assembly.


12. REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Disengage the clamp.

  1. Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.


13. DISCONNECT SUCTION PIPE SUB-ASSEMBLY

  1. E128510
    Remove the bolt, and slide the hook connector.

  1. Disconnect the suction pipe sub-assembly.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


14. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY
  1. Disconnect the air conditioning tube and accessory.

  1. Remove the O-ring from the air conditioner tube and accessory.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


15. DISCONNECT HEATER WATER HOSE OUTLET

  1. E128511
    Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.


16. DISCONNECT HEATER WATER HOSE INLET

HINT:
Disconnection procedure for the heater inlet water hose is the same as that for the heater outlet water hose.


17. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.

    C146012E01

    HINT:
    Tape up the screwdriver tip before use.


18. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.

    C146013E01

    HINT:
    Tape up the screwdriver tip before use.


19. REMOVE STEERING PAD

  1. Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    C146014E01

  1. C133859E01
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector from the steering pad.

  1. Disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


20. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C145839E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


21. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


22. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


23. REMOVE LOWER NO.1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


24. REMOVE STEERING COLUMN COVER

  1. B137294E01
    Remove the 2 screws <D>.

  1. Disengage the 2 claws and remove the lower steering column cover.

  1. Disengage the claw and remove the upper steering column cover.


25. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C145843
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


26. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)

  1. B149938
    Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the No. 1 instrument panel sub-assembly.


27. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

  1. B149936
    Disengage the 3 claws and the 2 clips.

  1. Disconnect the connector and remove the No. 1 instrument panel sub-assembly.


28. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B144612
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.


29. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)

  1. B159330
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.

  1. Disconnect the connector.


30. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Remove the 2 clips.

  1. Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.


31. REMOVE COMBINATION METER ASSEMBLY

  1. B152781E01
    Remove the 4 screws <E>.

  1. Disconnect each connector and remove the combination meter assembly.


32. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


33. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


34. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133988E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


35. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B133992E01
    Remove the bolt <A>.

  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.


36. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B148446
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


37. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B152779
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


38. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B152774
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


39. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144599
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


40. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144605
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


41. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)

  1. B148447
    Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.


42. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)

  1. B152776E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B152777
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.


43. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B144607E02
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B144602
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.


44. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B149934
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


45. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


46. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


47. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY

  1. B141243E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.

    HINT:
    Set the shift lever in the D position.


48. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY

  1. B152782E01
    Apply protective tape to the areas shown in the illustration.

  1. B152783
    Using a moulding remover, disengage the 3 clips.

  1. B152784
    Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.


49. REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player)

  1. E135568
    Remove the 4 bolts.

  1. Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.


50. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player)

  1. E129175
    Remove the 4 bolts.

  1. Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver with heater control panel assembly.


51. REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)

  1. E137564
    Remove the 4 bolts.

  1. Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver with heater control panel assembly.


52. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.


53. REMOVE CONSOLE BOX CARPET

  1. B134004
    Remove the console box carpet.


54. REMOVE CONSOLE BOX ASSEMBLY

  1. B134002E01
    Remove the 2 screws <F>.

  1. B149935E03
    Disengage the clamp.

  1. Remove the 2 bolts <G> and the console box assembly.


55. REMOVE NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.


56. REMOVE NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.


57. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.


58. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.

  1. B132100E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


59. REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY

  1. B134007
    Disengage the 4 clips and remove the instrument panel No. 1 register assembly.


60. REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY

  1. B134009E01
    Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.


61. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for 6 Speakers)

  1. E129167
    Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.


62. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.


63. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.

  1. B132099E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


64. REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY

  1. B134008
    Disengage the 4 clips and remove the instrument panel No. 3 register assembly.


65. REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY

  1. B134010E01
    Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.


66. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for 6 Speakers)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


67. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH

  1. B134011E01
    Disengage the 8 clips and the 4 guides.

  1. Disconnect each connector and remove the No. 1 defroster nozzle garnish.


68. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C132564E01
    Disconnect the connector (yellow colored one).


69. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disengage each clamp.

  1. Disconnect each connector.

  1. Remove the bolt <J>.

  1. Remove the 2 passenger airbag bolts <C>.

    B134013E01

  1. Remove the 2 bolts <H>.

  1. Remove the 2 nuts <I>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B134014E06


70. REMOVE NO. 1 CONSOLE BOX DUCT

  1. C129716
    Remove the clip and No. 1 console box duct.


71. REMOVE FLOOR CARPET BRACKET LH

  1. E129146E01
    Release the clamp.

  1. Turn back the floor carpet.

  1. E128512
    Remove the 3 clips.

  1. Remove the floor carpet bracket LH.


72. REMOVE FLOOR CARPET BRACKET RH

  1. E129147E01
    Release the clamp.

  1. Turn back the floor carpet.

  1. E128513
    Remove the 3 clips.

  1. Remove the floor carpet bracket RH.


73. REMOVE REAR NO. 2 AIR DUCT

  1. E135675
    Release the 2 claws and remove the rear No. 2 air duct.


74. REMOVE REAR NO. 1 AIR DUCT

  1. E135676
    Release the 2 claws and remove the rear No. 1 air duct.


75. REMOVE NO. 1 AIR DUCT

  1. C132547E01
    Disengage the 2 claws and remove the No. 1 air duct.


76. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C133172
    Remove the clamp from the steering column hole shield.

  1. C132548E02
    Remove the bolt.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C132549E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


77. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.

  1. C145844E01
    Remove the bolt, 2 nuts, and the steering column assembly.


78. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E128518E01
    Disconnect the 2 connectors.

  1. Remove the 2 bolts and air conditioning amplifier assembly.


79. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Remove the 28 clamps, disconnect the 11 connectors, and then disconnect the wire harness.

  1. Remove the 6 nuts, 7 bolts, and junction block.

    E136484E01

  1. Remove the 2 caps and 2 bolts from the engine compartment side.

    E128520

  1. Remove the 2 bolts and nut.

  1. Using a "TORX" socket wrench (T40), remove the 5 "TORX" bolts.

    E128521E02

    HINT:
    The "TORX" bolts on the passenger side can be removed with the collars for adjustment.

  1. Using a 12 mm hexagon wrench, remove the 2 collars and instrument panel reinforcement assembly with the air conditioner unit assembly.

  1. Remove the 3 bolts, 2 screws, and instrument panel reinforcement assembly.

    E128522


80. REMOVE BLOWER ASSEMBLY

  1. E129996
    Remove the connector and clamp, and disconnect the wire harness.

  1. E129997
    Remove the 6 screws and then the blower assembly with the cooler evaporator sub-assembly.

← COMPONENTS (from Jun 2009)REMOVAL (from Jun 2009) →