Steering Pad Switch Circuit
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
AUTO, OFF, TEMP UP (+), and TEMP DOWN (-) switches are located on the steering pad switch. The resistance of the steering pad switch changes in accordance with switch operation. The A/C control assembly outputs voltage to the steering pad switch and reads voltage changes due to the resistance changes that result from switch operation.- HINT:
- If there is an open in the circuit, the A/C system cannot be operated by the steering pad switch assembly.
- If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the A/C control assembly cannot be operated by the steering pad switch assembly, and the A/C control assembly will not be able to function correctly.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT A/C CONTROL ASSEMBLY |
Remove the A/C control assembly with the connectors still connected.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection (Symbols)
Condition
Specified Condition
F16-9 (ADI1) - F16-8 (SG)
AUTO switch: ON
Below 2.5 Ω
F16-9 (ADI1) - F16-8 (SG)
OFF switch: ON
Approx. 329 Ω
F16-9 (ADI1) - F16-8 (SG)
TEMP+ switch: ON
Approx. 1,000 Ω
F16-9 (ADI1) - F16-8 (SG)
TEMP- switch: ON
Approx. 3,110 Ω
|
|
||||
| OK | ||
| ||
| 2. INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly.
Disconnect the connector from the steering pad switch assembly.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection (Symbols)
Condition
Specified Condition
a1-3 (AC1) - a1-2 (EAC)
AUTO switch: ON
Below 2.5 Ω
a1-3 (AC1) - a1-2 (EAC)
OFF switch: ON
Approx. 329 Ω
a1-3 (AC1) - a1-2 (EAC)
TEMP+ switch: ON
Approx. 1,000 Ω
a1-3 (AC1) - a1-2 (EAC)
TEMP- switch: ON
Approx. 3,110 Ω
|
|
||||
| OK | |
| 3. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the connector from the spiral cable sub-assembly.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection (Symbols)
Condition
Specified Condition
E18-10 (AC1) - a1-3 (AC1)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
E18-9 (EAC) - a1-2 (EAC)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- HINT:
- The spiral cable makes a maximum of approximately 5 rotations.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (A/C CONTROL ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY) |
Disconnect the connector from the A/C control assembly.

Disconnect the connector from the spiral cable sub-assembly.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
F16-9 (ADI1) - E18-10 (AC1)
Always
Below 1 Ω
F16-8 (SG) - E18-9 (EAC)
Always
Below 1 Ω
F16-9 (ADI1) - Body ground
Always
10 kΩ or higher
F16-8 (SG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
