2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL RADIATOR SUPPORT LOWER

  1. A133371E03
    Install the 2 radiator support lowers to the radiator assembly.


2. INSTALL RADIATOR SUPPORT CUSHION

  1. A133371E02
    Install the 2 radiator support cushions to the radiator assembly.


3. INSTALL FAN ASSEMBLY WITH MOTOR

  1. A143820E01
    Install the fan assembly with motor to the radiator with the 2 guides at the bottom and 3 snap fits on the top.


4. INSTALL RADIATOR ASSEMBLY

  1. A147104
    Install the radiator to the body.

  1. A135239
    Install the condenser assembly with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. A135241
    Connect the 2 fan motor connectors and the 3 clamps.


5. INSTALL RADIATOR SUPPORT UPPER

  1. A145802
    Install the radiator support upper with the 5 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. A146042E02
    Install the hood lock control cable assembly to the radiator support upper with the clamp.

  1. A145801
    Install the hood lock assembly to the radiator support upper with the 3 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

  1. Connect the horn connectors.


6. CONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)

  1. A128129
    Connect the oil cooler outlet hose to the radiator assembly.


7. CONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)

  1. A128128
    Connect the oil cooler inlet hose to the radiator assembly.


8. CONNECT RADIATOR HOSE OUTLET

  1. A128127
    Connect the radiator hose outlet to the radiator assembly.


9. CONNECT RADIATOR HOSE INLET

  1. A146041
    Connect the radiator hose inlet to the radiator assembly.


10. CONNECT RADIATOR RESERVOIR TANK HOSE

  1. A135233
    Connect the radiator reservoir tank hose to the radiator assembly.


11. INSTALL FRONT BUMPER ENERGY ABSORBER

  1. B150451
    Install the front bumper energy absorber to the front bumper reinforcement sub-assembly.


12. INSTALL FRONT BUMPER ASSEMBLY (w/ Fog Light)

  1. B150437
    Connect each connector.

  1. Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 2 clips, 2 radiator grille protectors and bolt.

  1. B137229
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


13. INSTALL FRONT BUMPER ASSEMBLY (w/o Fog Light)

  1. B150436
    Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 2 clips, 2 radiator grille protectors and bolt.

  1. B137229
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


14. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A134903
    Install the air cleaner inlet with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


15. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


16. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.7 liters (7.1 US qts, 5.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


17. INSPECT FOR COOLANT LEAK

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A135234
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


18. INSTALL ENGINE UNDER COVER LH

19. INSTALL ENGINE UNDER COVER RH
← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →