2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Oct 2006


1. INSTALL RADIATOR TANK UPPER

  1. A104624E02
    Install the punch assembly to the overhaul handle, inserting it in the hole in part A as shown in the illustration.
    SST
    09230-01010  
    09231-14010  

  1. While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

    Dimension B:
    7.40 to 7.80 mm (0.2913 to 0.3071 in.)

  1. A104623E03
    After checking that there are no foreign objects in the lock plate groove, install a new O-ring without twisting it.

    HINT:
    When cleaning the lock plate groove, lightly rub it with sand paper without scratching it.

  1. Install the tank without damaging the O-ring.

  1. A128141E01
    Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and the tank.

    NOTICE:
    Do not tap the areas protruding around the pipes, brackets or tank ribs.

  1. A129608E01
    Lightly press SST against the lock plate in the order shown in the illustration. After repeating this procedure a few times, fully crimp the lock plate by squeezing the handle until stopped by the stopper bolt.

  1. A144993
    Do not tap the areas protruding around the pipes, brackets or tank ribs.

  1. A144994
    Do not tap the area indicated by the circles in the illustration. For the areas where cannot be tapped with the SST, use pliers or similar objects and be careful not to damage the core plates.

  1. A128142E01
    Check the lock plate height (H) after completing caulking.

    Plate height (H):
    7.40 to 7.80 mm (0.2913 to 0.3071 in.)

    If not within the specified height range, adjust the stopper bolt of the handle and caulk again.

  1. Tap the lock plate with a soft-faced hammer so that there is no gap between the lock plate and the tank.


2. INSTALL OIL COOLER ASSEMBLY
  1. Clean the O-ring contact surfaces of the lower tank and oil cooler.

  1. A128140E05
    Install 2 new O-rings to the oil cooler (D).

  1. Install the oil cooler to the lower tank (C).

  1. Install the plate washer and nut (B).

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Install the cooler pipe with the bolt (A).

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }


3. INSTALL RADIATOR TANK LOWER

HINT:
Installation procedure of the radiator tank lower is the same as that of the radiator tank upper.


4. INSTALL DRAIN PLUG
  1. Install a new O-ring to the drain plug.

  1. Install the drain plug.


5. INSPECT FOR WATER LEAK

  1. A128143E03
    Plug the inlet and outlet pipes of the radiator with SST.
    SST
    09230-01010  

  1. Using the radiator cap tester, apply pressure to the radiator.

    Test pressure:
    177 kPa (1.8 kgf/cm2, 26 psi)

  1. Submerge the radiator in water.

  1. A087096E02
    Inspect for leaks.

    HINT:
    On radiators with resin tanks, there is clearance between the tank and lock plate where a minute amount of air will remain, giving the appearance of an air leak when the radiator is submerged in water. Therefore, before doing the water leak test, first swish the radiator around in the water until all air bubbles disappear.

← INSPECTION (from Oct 2006)INSTALLATION (Oct 2006 – May 2009) →