2006-2011 Camry Aurion · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
(Click here)

2. SECURE ENGINE
  1. Secure the engine onto an engine stand with the bolts.


3. REMOVE INTAKE AIR SURGE TANK ASSEMBLY

  1. A129464E01
    Disconnect the 2 water by-pass hoses from the throttle with motor body assembly.

  1. Disconnect the vapor feed hose.

  1. Disconnect the throttle with motor body assembly connector and clamp.

  1. Disconnect the No. 1 ventilation hose.

  1. A129466
    Remove the bolt and vacuum hose clamp.

  1. A129467
    Disconnect the connector.

  1. Remove the 4 bolts, No. 1 surge tank stay and throttle body bracket.

  1. A139209E01
    Using a 5 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and intake air surge tank.

  1. Remove the gasket from the intake air surge tank.


4. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 6 bolts and 6 ignition coils.


5. REMOVE NO. 2 A ENGINE MOUNTING STAY RH
  1. Remove the bolt and No. 2 A engine mounting stay RH.


6. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Disconnect the A/F sensor connector clamp.

  1. A129637
    Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.


7. REMOVE OIL LEVEL GAUGE GUIDE SUB-ASSEMBLY

  1. A129638
    Remove the oil level gauge.

  1. Remove the 2 bolts, oil level gauge guides No. 1 and No. 2.

  1. Remove the O-rings from the oil level gauge guide.


8. REMOVE NO. 2 MANIFOLD STAY

  1. A140783
    Remove the bolt, nut, and No. 2 manifold stay.


9. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A129640
    Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


10. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A129641
    Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.


11. REMOVE ENGINE MOUNTING BRACKET RH

  1. A129642
    Remove the 3 bolts and engine mounting bracket RH.


12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A129644
    Remove the 5 bolts and V-ribbed belt tensioner assembly.


13. REMOVE NO. 2 TIMING GEAR COVER

  1. A132987
    Remove the 2 bolts and No. 2 timing gear cover.


14. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A129645E03
    Remove the bolts, plates and No. 2 idler pulley sub-assemblies.


15. REMOVE WATER PUMP PULLEY

  1. A128112E03
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.


16. REMOVE RADIO SETTING CONDENSER

  1. A132991
    Remove the 2 bolts and 2 radio setting condensers.


17. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

  1. A132992
    Remove the bolt and No. 1 vacuum switching valve.


18. REMOVE NO. 1 OIL PIPE

  1. A135726E01
    Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter LH and gaskets.


19. REMOVE OIL PIPE

  1. A134878E01
    Remove the bolt.

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.


20. REMOVE CRANKSHAFT PULLEY

  1. A120690E02
    Using SST, loosen the crankshaft pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

  1. A120691E02
    Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


21. REMOVE NO. 1 ENGINE MOUNTING BRACKET FRONT LH

  1. A129672
    Remove the 6 bolts and engine mounting bracket.

  1. Using a "TORX" socket wrench E8, remove the 2 stud bolts.


22. REMOVE OIL COOLER PIPE

  1. A141494
    Remove the bolt and 2 nuts, and disconnect the oil cooler pipe from the oil pan sub-assembly.

  1. Remove the gasket from the oil pan sub-assembly.


23. REMOVE WATER INLET HOUSING

  1. A129673
    Remove the 2 nuts, water inlet, and thermostat.

  1. Remove the gasket.

  1. Remove the 2 stud bolts.

  1. Separate the No. 1 water by-pass hose.

  1. A134879E01
    Remove the 2 bolts, nut, and water inlet housing.

  1. Remove the drain cock plug.

  1. Remove the drain cock.

  1. A129675
    Remove the 2 O-rings.


24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A129679
    Remove the 12 bolts, seal washer, head cover, and gasket.

  1. A129699
    Remove the 3 gaskets.


25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A129678E02
    Remove the 12 bolts, seal washer, head cover, and gasket.

    NOTICE:
    The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the head cover.

  1. A129705
    Remove the 3 gaskets.


26. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A129680E01
    Remove the 16 bolts and 2 nuts.

  1. A120816
    Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.

  1. Using a "TORX" socket wrench E6, remove the 2 stud bolts.


27. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A129681
    Remove the bolt, 2 nuts, oil strainer, and gasket.

  1. Using a "TORX" socket wrench E6, remove the 2 stud bolts.


28. REMOVE OIL PAN SUB-ASSEMBLY

  1. A153328E01
    Remove the 16 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

  1. A129683E01
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A129684
    Remove the 2 O-rings.

  1. Using a "TORX" socket wrench E8, remove the 4 stud bolts.


29. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A128004
    Remove the 23 bolts and 2 nuts as shown in the illustration.

  1. A129690E02
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

    HINT:
    Tape the screwdriver tip before use.

  1. A128006E01
    Remove the gasket.


30. REMOVE TIMING CHAIN CASE OIL SEAL

  1. A128007E01
    Using a screwdriver, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (from Oct 2006) →