2006-2011 Camry Aurion · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.

    A128117E02

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E135586
    Remove the nut and the front wiper arm and blade assembly LH.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E135587
    Remove the nut and the front wiper arm and blade assembly RH.


6. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Disengage the claw and remove the front fender to cowl side seal LH.


7. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Disengage the claw and remove the front fender to cowl side seal RH.


8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

  1. E135588
    Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

  1. E140957
    Remove the 2 clips.

  1. Disengage the 3 claws and remove the cowl top ventilator louver sub-assembly.


10. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E135589
    Disconnect the connector.

  1. E135590
    Remove the 4 bolts and the windshield wiper motor and link assembly.


11. REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Disengage the clamp.

  1. Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.


12. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A140800
    Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.


13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A135704
    Disconnect the 3 vacuum hoses.

  1. A135705E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).

  1. A135706
    Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.


14. REMOVE INTAKE AIR SURGE TANK ASSEMBLY

  1. A129464E03
    Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)

  1. Disconnect the vapor feed hose. (*2)

  1. Disconnect the throttle with motor body assembly connector and clamp. (*3)

  1. A129465E08
    Disconnect the No. 1 ventilation hose. (*4)

  1. Disconnect the union to check valve hose. (*5)

  1. A129466
    Remove the bolt and vacuum hose clamp.

  1. A129467
    Disconnect the connector.

  1. A129468E06
    Using a 5 mm hexagon socket wrench, remove the 4 bolts. (*1)

  1. Remove the 2 nuts, 2 bolts and intake air surge tank. (*2)

  1. Remove the gasket from the intake air surge tank.


15. DISCONNECT FUEL TUBE SUB-ASSEMBLY

  1. A129469E02
    Remove the No. 2 fuel pipe clamp.

  1. Pinch the tube connector and then pull out the fuel pipe.

    NOTICE:
    1. Check that there is no dirt or other foreign objects around the connector before this operation and clean the connector as necessary.
    2. It is necessary to prevent mud or dirt from entering the quick connector. If mud enters the connector, the O-rings may not seal properly.
    3. Remove the quick connector by hand.
    4. Do not bend, kink, or twist the nylon tube. Protect the connector by covering it with a plastic bag.
    5. If the pipe and the connector are stuck, try wiggling or pushing and pulling the connector to release it and pull the connector out of the pipe carefully.


16. REMOVE FUEL INJECTOR ASSEMBLY

  1. A137341
    Disconnect the 6 fuel injector connectors.

  1. A129471
    Remove the 5 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  1. A129472
    Remove the 6 insulators from the intake manifold.

  1. A129473
    Pull out the fuel injectors from the fuel delivery pipe.

  1. A129475E02
    Remove the 6 O-rings from the injectors.

← COMPONENTS (from Oct 2006)REMOVAL (from Jun 2009) →