C0273/13 Open or Short Circuit in ABS Motor Relay Circuit
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.If the voltage supplied to the motor relay (+BM) is below the DTCs detection threshold due to low voltage from the battery or alternator, the DTC may be stored.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| C0273/13 |
When any of the following is detected:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- When C1241/41 is output together with C0273/13, inspect and repair the trouble areas indicated by C1241/41 (Click here).
- Check the condition of each related circuit connector before troubleshooting (Click here).
- When C1241/41 is output together with C0273/13, inspect and repair the trouble areas indicated by C1241/41 (Click here).
| 1. INSPECT FUSIBLE LINK (ABS NO. 1 FUSE) |
Remove the fusible link from the engine room R/B.

Check if the fusible link is melted.
- OK:
- The fusible link is not melted.
Install the fusible link to the engine room R/B with the nut.
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
|
|
||||
| OK | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Active Test" on the intelligent tester (Click here).
Active Test: ABS Tester Display
Test Part
Control Range
Normal Condition
Motor Relay
ABS motor relay
Motor relay ON/OFF
Operating sound of motor is heard
Check the operating sound of the ABS motor relay when operating it with the intelligent tester.
- OK:
- The operating sound of the ABS motor relay should be heard.
- Result:
Result
Proceed to
The operating sound is not heard
A
The operating sound is heard
B
|
|
||||
| A | |
| 3. INSPECT SKID CONTROL ECU CONNECTOR (+BM TERMINAL VOLTAGE) |
Disconnect the skid control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
A25-2 (+BM) -
Body ground
Always
10 to 14 V
|
|
||||
| OK | |
| 4. INSPECT SKID CONTROL ECU CONNECTOR (GND TERMINAL CONTINUITY) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Specified Condition
A25-4 (GND1) - Body ground
Below 1 Ω
A25-1 (GND2) - Body ground
Below 1 Ω
Connect the connector.
|
|
||||
| OK | |
| 5. RECONFIRM DTC |
- HINT:
- This code is detected when a problem is identified in the brake actuator assembly.
- The ABS motor relay is in the brake actuator assembly.
- Therefore, ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTC is not output
A
DTC is output
B
- HINT:
- If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
- If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
- It is suspected that the DTCs were output due to a bad connection of the connector terminal.
- If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
|
|
||||
| A | ||
| ||
