2006-2011 Camry Aurion · Service Manual BRAKE

C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This relay supplies power to each ABS solenoid. If the ABS initial check is OK after the ignition switch is turned to the ON position, the skid control ECU will turn the ABS solenoid relay on.
DTC No.
DTC Detecting Condition
Trouble Area
C0278/11
When any of the following is detected:
  1. 3 or more solenoid valves are found faulty and simultaneously valve supply voltage is detected to be abnormal.
  2. Solenoid valve relay is not switched off.
  3. Valve relay is stuck open even through the valve relay supply voltage is high.
  1. Wire harness (+BS circuit)
  2. ABS No. 2 fuse (Fusible link)
  3. Brake actuator assembly (Solenoid relay)

WIRING DIAGRAM

C144435E06

INSPECTION PROCEDURE

HINT:
  1. When C1241/41 is output together with C0278/11, inspect and repair the trouble areas indicated by C1241/41 (Click here).
  2. Check the condition of each related circuit before troubleshooting (Click here).


1. INSPECT FUSIBLE LINK (ABS NO. 2 FUSE)

  1. C136500E02
    Remove the fusible link from the engine room R/B.

  1. Check if the fusible link is melted.

    OK:
    The fusible link is not melted.

  1. Install the fusible link to the engine room R/B with the nut.

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



NG
REPLACE FUSIBLE LINK
OK


2. INSPECT SKID CONTROL ECU CONNECTOR (+BS TERMINAL VOLTAGE)

  1. C131970E10
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-3 (+BS) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK


3. INSPECT SKID CONTROL ECU CONNECTOR (GND TERMINAL CONTINUITY)

  1. C131970E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A25-4 (GND1) - Body ground
    Below 1 Ω
    A25-1 (GND2) - Body ground
    Below 1 Ω

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4. RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The solenoid circuit is in the brake actuator assembly.
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Condition
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    1. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    2. If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
    3. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit (Oct 2006 – May 2009)C1237/37 Speed Sensor Rotor Faulty (Jun 2006 – Sep 2006) →