Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM
Brake Warning Light Remains ON
Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The skid control ECU sends the indicator signals to the combination meter assembly via the CAN communication system. If any of the following is detected, the brake warning light remains on:
The skid control ECU connector is disconnected from the skid control ECU.
The brake fluid level is insufficient.
The parking brake is applied.
EBD operation is not possible.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Check the condition of each related circuit connector before troubleshooting (Click here ).
1. INSPECT CAN COMMUNICATION SYSTEM
Check if a CAN communication system DTC is output (Click here ).
Result:
Condition
Proceed to
DTC is not output
A
DTC is output
B
B
A
2. CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
Check if the skid control ECU connector is securely connected.
OK:
The connector should be securely connected.
NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK
3. CHECK BATTERY
Check the battery voltage.
Standard voltage:
11 to 14 V
NG
OK
4. INSPECT SKID CONTROL ECU CONNECTOR (IG1 TERMINAL VOLTAGE)
Disconnect the skid control ECU connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
A25-18 (IG1) - Body ground
Ignition switch ON
10 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK
5. INSPECT SKID CONTROL ECU CONNECTOR (GND TERMINAL CONTINUITY)
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
A25-4 (GND1) - Body ground
Always
Below 1 Ω
A25-1 (GND2) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK
6. INSPECT PARKING BRAKE SWITCH
Remove the parking brake switch.
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Automatic Transaxle:
Tester Connection
Condition
Specified Condition
(A18-1) - Ground part
Free
Below 1 Ω
(A18-1) - Ground part
Pushed in
10 kΩ or higher
Manual Transaxle:
Tester Connection
Condition
Specified Condition
(E33-1) - Ground part
Free
Below 1 Ω
(E33-1) - Ground part
Pushed in
10 kΩ or higher
NG
REPLACE PARKING BRAKE SWITCH
OK
7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU TO PARKING BRAKE SWITCH)
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Automatic Transaxle:
Tester Connection
Specified Condition
IC-14 - A18-1 (PKB)
Below 1 Ω
A18-1 (PKB) - Body ground
10 kΩ or higher
Manual Transaxle:
Tester Connection
Specified Condition
IM-2 (PKB) - E33-1 (PKB)
Below 1 Ω
E33-1 (PKB) - Body ground
10 kΩ or higher
Connect the connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU TO PARKING BRAKE SWITCH)
OK
8. INSPECT BRAKE FLUID LEVEL WARNING SWITCH ASSEMBLY
Remove the reservoir tank cap.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
HINT:
A float is located inside the reservoir.
Its position can be changed by increasing or decreasing the level of brake fluid.
Standard resistance:
Tester Connection
Condition
Specified Condition
(A16-1) - (A16-2)
Float UP (Switch OFF)
10 kΩ or higher (No Continuity)
(A16-1) - (A16-2)
Float DOWN (Switch ON)
Below 1 Ω (Continuity)
HINT:
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
OK
9. CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH TO COMBINATION METER)
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
A16-1 - F1-15 (B/LE)
Always
Below 1 Ω
F1-15 (B/LE) - Body ground
Always
10 kΩ or higher
A16-2 - Body ground
Always
Below 1 Ω
Connect the connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH TO COMBINATION METER)
OK
10. INSPECT COMBINATION METER ASSEMBLY
Connect the intelligent tester to the DLC3.
Select the "Active Test" on the tester (Click here ).
Active Test: ABS
Tester Display
Test Part
Control Range
Diagnostic Note
Brake Warning Lamp
Brake warning light
Warning light ON/OFF
Observe combination meter
Check the ABS warning light operation.
OK:
The brake warning light turns on or off in accordance with the intelligent tester.
NG
OK