B2312 Driver Side Door Master Switch Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2006
DESCRIPTION
The portion of the power window control system that is located in the driver door consists of a power window master switch, regulator, and a motor with an integrated ECU. The driver door power window regulator motor is controlled by the ECU when the power window master switch is operated (models with jam protection).When the ECU determines that the power window master switch is stuck, DTC B2312 is set.
- NOTICE:
- The power window control system uses a serial communication protocol (LIN) to communicate with the main body ECU. Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
The power window regulator master switch is stuck |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Using the data list to check the function of the power window power window ECU (Power window regulator motor).
D DOOR MOTOR: Item
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Auto SW
Driver door power window auto switch signal/ON or OFF
ON: Driver door power window auto switch operates
OFF: Driver door power window auto switch does not operate
-
D Door Up SW
Driver door power window manual up switch signal/ON or OFF
ON: Driver door power window manual up switch operates
OFF: Driver door power window manual up switch does not operate
-
D Door Down SW
Driver door power window manual down switch signal/ON or OFF
ON: Driver door power window manual down switch operates
OFF: Driver door power window manual down switch does not operate
-
- OK:
- ON (switch operates) appears on screen.
- HINT:
- When the power window operates normally, the problem has been caused by irregular switch operation (for example, the power window regulator master switch was held in the same position for more than 20 seconds).
|
|
||||
| NG | |
| 2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
![]() ![]() |
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LHD models:
Tester Connection
Condition
Specified Condition
8 (U) - 1 (E) - 4 (A)
Auto UP
Below 1 Ω
8 (U) - 1 (E)
Manual UP
Below 1 Ω
8 (U) - 5 (D) - 6 (B)
OFF
Below 1 Ω
5 (D) - 1 (E)
Manual DOWN
Below 1 Ω
4 (A) - 5 (D) - 1 (E)
Auto DOWN
Below 1 Ω
- RHD models:
Tester Connection
Condition
Specified Condition
1 (U) - 9 (E) - 4 (A)
Auto UP
Below 1 Ω
1 (U) - 9 (E)
Manual UP
Below 1 Ω
1 (U) - 5 (D) - 6 (B)
OFF
Below 1 Ω
5 (D) - 9 (E)
Manual DOWN
Below 1 Ω
4 (A) - 5 (D) - 9 (E)
Auto DOWN
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (WINDOW REGULATOR MASTER SWITCH - WINDOW REGULATOR ECU) |
Disconnect the M1 (*1), L1 (*2) and I5 (*1), H10 (*2) connectors.

- HINT:
- *1: LHD models
- *2: RHD models
- *1: LHD models
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LHD models:
Tester Connection
Condition
Specified Condition
M1-8 (U) - I5-10 (UP1)
Always
Below 1 Ω
M1-3 (LED) - I5-5 (LED)
Always
Below 1 Ω
M1-4 (A) - I5-4 (AUTO)
Always
Below 1 Ω
M1-5 (D) - I5-7 (DWN1)
Always
Below 1 Ω
M1-8 (U) - Body ground
Always
10 kΩ or higher
M1-3 (LED) - Body ground
Always
10 kΩ or higher
M1-4 (A) - Body ground
Always
10 kΩ or higher
M1-5 (D) - Body ground
Always
10 kΩ or higher
- Standard resistance:
- RHD models:
Tester Connection
Condition
Specified Condition
L1-1 (U) - H10-10 (UP1)
Always
Below 1 Ω
L1-3 (LED) - H10-5 (LED)
Always
Below 1 Ω
L1-4 (A) - H10-4 (AUTO)
Always
Below 1 Ω
L1-5 (D) - H10-7 (DWN1)
Always
Below 1 Ω
L1-1 (U) - Body ground
Always
10 kΩ or higher
L1-3 (LED) - Body ground
Always
10 kΩ or higher
L1-4 (A) - Body ground
Always
10 kΩ or higher
L1-5 (D) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||

