2006-2011 Camry Aurion · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that receive power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.

A116143E14

WIRING DIAGRAM

A140754E02
A140755E01

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) illuminates up when turning the ignition switch on (IG).

    OK:
    MIL lights up.



OK
GO TO MIL CIRCUIT (Click here)
NG


2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Check the communication between the tester and ECM.

    Result:
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3. CHECK THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4. CHECK ACCELERATOR PEDAL ASSEMBLY (CHECK MIL ILLUMINATED)
  1. Disconnect the accelerator pedal assembly connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal assembly connector.



A
REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)
B


5. CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for intake camshaft bank 1.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the connector to the VVT sensor for intake camshaft bank 1.



A
REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (Click here)
B


6. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 1.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 1.



A
REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (Click here)
B


7. CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for intake camshaft bank 2.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the connector to the VVT sensor for intake camshaft bank 2.



A
REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (Click here)
B


8. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 2.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 2.



A
REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (Click here)
B


9. CHECK HARNESS AND CONNECTOR

  1. A107934E31
    Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal assembly connector.

  1. Disconnect the connector from VVT sensor for intake camshaft bank 1.

  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 1.

  1. Disconnect the connector from the VVT sensor for intake camshaft bank 2.

  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 2.

  1. Disconnect the C58 (RHD) and A24 (RHD), or C55 (LHD) and A55 (LHD) ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    VCTA (C58-96) - Body ground
    10 kΩ or higher
    VCV1 (C58-115) - Body ground
    10 kΩ or higher
    VCV2 (C58-113) - Body ground
    10 kΩ or higher
    VCE1 (C58-114) - Body ground
    10 kΩ or higher
    VCE2 (C58-112) - Body ground
    10 kΩ or higher
    VCPA (A24-57) - Body ground
    10 kΩ or higher
    VCP2 (A24-58) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    VCTA (C55-96) - Body ground
    10 kΩ or higher
    VCV1 (C55-115) - Body ground
    10 kΩ or higher
    VCV2 (C55-113) - Body ground
    10 kΩ or higher
    VCE1 (C55-114) - Body ground
    10 kΩ or higher
    VCE2 (C55-112) - Body ground
    10 kΩ or higher
    VCPA (A55-57) - Body ground
    10 kΩ or higher
    VCP2 (A55-58) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connectors.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 2.

  1. Reconnect the connector to the VVT sensor for intake camshaft bank 2.

  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 1.

  1. Reconnect the connector to the VVT sensor for intake camshaft bank 1.

  1. Reconnect the accelerator pedal assembly connector.

  1. Reconnect the throttle body connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← VC Output Circuit (Oct 2006 – May 2009)Fuel Pump Control Circuit (Oct 2006 – May 2009) →