2006-2011 Camry Aurion · Service Manual BRAKE

C0273/13 Open or Short Circuit in ABS Motor Relay Circuit

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the skid control ECU switches the motor relay on and operates the ABS pump motor.
If the voltage supplied to the motor relay (+BM) is below the DTCs detection threshold due to low voltage from the battery or alternator, the DTC may be stored.
DTC No.
DTC Detection Condition
Trouble Area
C0273/13
When any of the following is detected:
  1. When the motor relay is actuated, voltage is not supplied to the pump motor within 0.1 seconds.
  2. For 30 to 125 ms after the motor relay is turned from ON to OFF, the remaining high voltage is out of range. The motor relay is turned from ON to OFF 3 times. If the voltage is still out of range in the 3rd operation, this failure is detected.
  3. When the motor relay is changed from ON to OFF, the remaining high voltage is more than 2 V for 1 second.
  1. ABS No. 1 fuse (Fusible link)
  2. Brake actuator assembly (Motor relay)
  3. Motor relay circuit

WIRING DIAGRAM

C144435E09

INSPECTION PROCEDURE

HINT:
  1. When C1241/41 is output together with C0273/13, inspect and repair the trouble areas indicated by C1241/41 (Click here).
  2. Check the condition of each related circuit connector before troubleshooting (Click here).


1. INSPECT FUSIBLE LINK (ABS NO. 1 FUSE)

  1. C136500E04
    Remove the fusible link from the engine room R/B.

  1. Check if the fusible link is melted.

    OK:
    The fusible link is not melted.

  1. Install the fusible link to the engine room R/B with the nut.

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



NG
REPLACE FUSIBLE LINK
OK


2. INSPECT SKID CONTROL ECU (+BM TERMINAL VOLTAGE)

  1. C136493E12
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A26-2 (+BM) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)
OK


3. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)

  1. C136493E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-4 (GND1) - Body ground
    Below 1 Ω
    A26-1 (GND2) - Body ground
    Below 1 Ω

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select "Active Test" on the intelligent tester (Click here).

    Active Test: ABS/TRC/VSC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Motor relay ON/OFF
    Operating sound of motor is heard

  1. Check the operating sound of the ABS motor relay when operating it with the intelligent tester.

    OK:
    The operating sound of the ABS motor relay is heard.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


5. RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The ABS motor relay is located in the brake actuator assembly.
Therefore, ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    1. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly (skid control ECU). Make sure that no DTCs are output.
    2. If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.
    3. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C0273/13 Open or Short Circuit in ABS Motor Relay Circuit (Jun 2006 – Sep 2006)C0273/13 Open or Short Circuit in ABS Motor Relay Circuit (from Jun 2009) →