2006-2011 Camry Aurion · Service Manual BRAKE

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


SYSTEM DESCRIPTION

HINT:
  1. The skid control ECU is located within the brake actuator assembly.
  2. The yaw rate sensor and acceleration sensor are combined in a single unit. This unit communicates with the skid control ECU through the CAN communication system.

  1. ABS operation

    1. Based on the signals received from the 4 wheel speed sensors, the skid control ECU calculates the deceleration and speed of each wheel, while monitoring for wheel lock. If wheel lock is occurring, the ECU controls the solenoid valves in the brake actuator in order to adjust the hydraulic pressure applied to the brakes at each wheel.


FUNCTION DESCRIPTION

  1. ABS (Anti-lock Brake System)
    The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
    C132003E01

    1. Operation description
      The skid control ECU detects wheel lock condition by receiving vehicle speed signals from each speed sensor, and sends control signals to the pump motor and solenoid valves.
      The pump motor and solenoid valves avoid wheel lock by controlling the hydraulic pressure of each wheel cylinder.
      The ABS warning light comes on when the ABS system is malfunctioning.

  2. EBD (Electronic Brake force Distribution)
    The EBD control utilizes ABS, which ensures proper brake force distribution between the front and rear wheels in accordance with driving conditions. In addition, when braking while cornering, it also controls the brake forces of the right and left wheels, helping to maintain vehicle behavior.
    C132004E02

    1. Operation description
      The skid control ECU receives a speed signal from each speed sensor, and uses these signals to detect locking of the wheels. The ECU uses this information in order to determine appropriate control of the solenoid valves.
      The solenoid valves control the hydraulic pressure applied to the brake cylinder at each wheel. In this way, the solenoid valves are used to control the brake power split between the front and rear, and left and right wheels. The BRAKE warning light comes on if there is a malfunction in the EBD system.

  3. BA (Brake Assist)
    The primary purpose of the brake assist system is to provide auxiliary brake force to assist a driver who cannot generate a large enough brake force during emergency braking. This system helps to maximize the brake performance of the vehicle.
    C132010E02

    1. Operation description
      The skid control ECU receives the speed signal from each speed sensor and the hydraulic pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is considered to be necessary, the skid control ECU sends control signals to the pump motor and solenoid valve.
      The pump motor and solenoid valve then control the pressure applied to each wheel cylinder.
      The ABS warning light comes on to indicate a malfunction in the BA (brake assist) system.

  4. TRC (Traction Control)
    The TRC system helps prevent the drive wheel from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
    C205842E07

    1. Operation description
      The skid control ECU detects wheelspin condition by receiving signals from each speed sensor and the ECM via CAN communication.
      The skid control ECU controls engine torque with the ECM via CAN communication and brake hydraulic pressure through the pump motor and solenoid valve.
      The SLIP indicator light blinks when the system is operating. If a malfunction occurs in the TRC system, the SLIP indicator lights will come on.

  5. VSC (Vehicle Stability Control)
    The VSC system helps prevent the vehicle from slipping sideways as a result of a strong front or rear wheel skid during cornering.
    C205843E05

    1. Operation description
      The skid control ECU determines the vehicle operating conditions based on signals received from the wheel speed sensors, yaw rate and acceleration sensor, and steering angle sensor. The skid control ECU sends signals via CAN communication to the ECM in order to control engine torque. The skid control ECU controls brake hydraulic pressure using the pump motor and solenoid valves.
      The SLIP indicator light will blink, and the skid control buzzer will sound when the system is operating. If a malfunction occurs in the VSC system, the SLIP indicator light will come on.


ABS with EBD, BA, TRC and VSC OPERATION
  1. The skid control ECU calculates vehicle stability tendency based on the signals from the speed sensor, yaw rate and acceleration sensor, and steering angle sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the wheel brake pressure by the brake actuator assembly) should be implemented.

  2. The SLIP indicator blinks and the skid control buzzer sounds to inform the driver that the VSC system is operating. The SLIP indicator also blinks when traction control is operating, and the operation being performed is displayed.


FAIL SAFE
  1. When a failure occurs in the ABS with BA, TRC and VSC systems, the ABS warning light and SLIP indicator light come on and ABS with BA, TRC and VSC operations are prohibited. In addition, when there is a failure that disables the EBD operation, the BRAKE warning light also comes on and the EBD operation is prohibited.

  2. If control is prohibited due to a malfunction during operation, control will be disabled gradually. This is to avoid sudden vehicle instability.


INITIAL CHECK
  1. When the vehicle speed first becomes approximately 6 km/h (4 mph) or more after the ignition switch on (IG), each solenoid valve and motor of the brake actuator assembly is sequentially activated to perform an electrical check. During the initial check, the operating sound of the solenoid valve and motor can be heard from the engine compartment, but this is not a malfunction.


FUNCTION OF COMPONENTS
Components
Function
Brake actuator assembly
  1. Changes the fluid path based on the signals from the skid control ECU during the operation of the ABS with EBD & BA & TRC & VSC system, in order to control the fluid pressure that is applied to the wheel cylinders.
  2. Houses the skid control ECU.
Skid control ECU
  1. Housed in the brake actuator assembly.
  2. Judges the vehicle driving condition based on the signals from each sensor, and controls the brake actuator assembly.
  3. Sends and receives the control signals to or from the ECM, yaw rate and acceleration sensor, and steering angle sensor via CAN communication.
Master cylinder pressure sensor
Detects the fluid pressure in the master cylinder.
Speed sensor
Detects speed of each wheel and inputs the data into the skid control ECU.
Stop light switch
Illuminates the brake light when the brake pedal is depressed. (Sends a brake on signal to the skid control ECU)
Motor relay
  1. Supplies power to the pump motor.
  2. Housed in the skid control ECU.
Solenoid relay
  1. Supplies power to each solenoid valve.
  2. Housed in the skid control ECU.
ECM
  1. Controls the engine output based on the signals received from the skid control ECU.
  2. Sends the accelerator pedal position signal and the engine speed signal to the skid control ECU.
ABS warning light
  1. Comes on to inform the driver that a malfunction in the ABS, EBD or BA (Brake Assist) has occurred.
  2. Blinks to output DTC.
BRAKE warning light
  1. Comes on to inform the driver that the parking brake is ON when the system is normal.
  2. Comes on to inform the driver that a malfunction in the EBD has occurred.
SLIP indicator light
  1. Blinks to inform the driver that TRC and VSC are operating.
  1. Blinks to output DTC.
Brake fluid level warning switch
Detects the brake fluid level.
Skid control buzzer
Intermittently sounds to inform the driver that the VSC is operating.
Yaw rate and acceleration sensor
  1. Acceleration sensor measures the capacity of the condenser that changes the distance between the electrodes depending on G force, which occurs when the vehicle is accelerated, and converts the measured value into electrical signals.
  2. Yaw rate sensor detects the vehicle's angular velocity (yaw rate) in the vertical direction based on the amount and direction of the piezoelectric ceramics deflection.
  3. Sends signals to the skid control ECU via CAN communication.
Steering angle sensor
  1. Installed in the steering column.
  2. Detects the steering amount and direction and sends the signals to the skid control ECU via CAN communication.
  3. Has the magnetic resistance element, which detects the rotation of the magnet housed in the detection gear in order to detect the changes in magnetic resistance and the steering amount and direction.
← SYSTEM DESCRIPTION (Oct 2006 – May 2009)HOW TO PROCEED WITH TROUBLESHOOTING (Jun 2006 – Sep 2006) →