2006-2011 Camry Aurion · Service Manual ENGINE

U0101 Lost Communication with TCM

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine rpm, required engine torques, warning indicators in the combination meter, DTCs and other data. The ECM sends signals to the TCM concerning engine rpm, opening angles of the throttle valve, temperature of intake air, temperature of engine coolant, engine torques and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and set a DTC.
DTC No.
DTC Detection Condition
Trouble Area
U0101
No communication from TCM continues
  1. Open or short in TCM and ECM circuit
  2. TCM
  3. ECM

WIRING DIAGRAM

A149032E01

INSPECTION PROCEDURE


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    U0101
    A
    U0101 and other DTCs
    B



B
GO TO DTC CHART (Click here)
A


2. CHECK TCM (+B AND E1 TERMINALS)

  1. C133210E08
    Disconnect the TCM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the TCM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    C56-18 (+B) - C56-8 (E1)
    9 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance of the TCM connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    C56-8 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR

  1. C133242E06
    Disconnect the C56 TCM connector.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    RHD:
    Tester Connection
    Specified Condition
    CAN+ (C56-6) - CAN+ (C58-2)
    Below 1 Ω
    CAN- (C56-7) - CAN- (C58-1)
    Below 1 Ω
    CAN+ (C56-6) or CAN+ (C58-2) - Body ground
    1 MΩ or higher
    CAN- (C56-7) or CAN- (C58-1) - Body ground
    1 MΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    CAN+ (C56-6) - CAN+ (C55-2)
    Below 1 Ω
    CAN- (C56-7) - CAN- (C55-1)
    Below 1 Ω
    CAN+ (C56-6) or CAN+ (C55-2) - Body ground
    1 MΩ or higher
    CAN- (C56-7) or CAN- (C55-1) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).

    CAUTION:
    Replace the ECM with the ECM of normally functioning vehicle of the same model.


NEXT


5. CHECK IF DTC RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC.

  1. Start the engine.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    U0101
    A
    No DTC
    B



B
REPLACE ECM (Click here)
A

REPLACE TCM (Click here)


← P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (+ P2A03) (from Jun 2009)U0101 Lost Communication with TCM (from Jun 2009) →