2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.


1. INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY

  1. B148636
    Install the front separate type seatback spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH

  1. B148654
    Install the upper reclining adjuster inside cover LH with the screw.


3. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH

  1. B148655
    Install the upper reclining adjuster inside cover RH with the screw.


4. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH

  1. B148653
    Engage the claw.

  1. Install the lower reclining adjuster inside cover LH with the screw.


5. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH

  1. B148652
    Engage the claw.

  1. Install the lower reclining adjuster inside cover RH with the screw.


6. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Except Sports Seat Type)

  1. B148637E01
    Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 12 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


7. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Sports Seat Type)

  1. B144038E01
    Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 14 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


8. INSTALL FRONT SEATBACK ASSEMBLY (for Except Sports Seat Type)
  1. Install the front seatback assembly to the front seatback spring assembly.

  1. B165264
    Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. B149612E01
    Engage the 6 hooks.

  1. Using hog ring pliers, install 5 new hog rings.

  1. B148638E01
    Using hog ring pliers, install 3 new hog rings.


9. INSTALL FRONT SEATBACK ASSEMBLY (for Sports Seat Type)

  1. B165264
    Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. Engage the 3 hooks.

  1. B165282E01
    Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


10. INSTALL FRONT SEAT HEADREST SUPPORT

  1. B146662
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


11. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Except Sports Seat Type)

  1. B146660
    Engage the 4 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


12. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Sports Seat Type)

  1. B134682E02
    Engage the 2 claws.

  1. Engage the 14 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


13. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Except Sports Seat Type)

  1. B148639E01
    Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 14 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


14. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Sports Seat Type)

  1. B144037E01
    Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 14 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


15. INSTALL FRONT SEAT CUSHION ASSEMBLY

  1. B148649
    Engage the hooks and install the front seat cushion assembly.


16. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B147690E01
    for LHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. B151307E02
      Connect the connectors and engage each clamp.

    3. B152832
      Engage the 2 hooks.

  1. B153036E01
    for RHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.


17. INSTALL FRONT INNER SEAT CUSHION SHIELD
  1. Engage the 2 claws.

  1. B157884
    Install the front inner seat cushion shield with the screw.


18. INSTALL FRONT SEAT CUSHION SHIELD
  1. Engage the 2 claws.

  1. B166773
    Install the front seat cushion shield with the 2 screws.

  1. B148646
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


19. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B166774
    Engage the claw to install the reclining adjuster release handle.

← DISASSEMBLY (from Jun 2009)REASSEMBLY (from Jun 2009) →