2006-2011 Camry Aurion · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. REMOVE LUGGAGE COMPARTMENT DOOR COVER

  1. B135465
    Using a clip remover, remove the 13 clips and luggage compartment door cover.


2. REMOVE REAR LIGHT ASSEMBLY LH

  1. E133813E01
    Disconnect the connector and clamp.

  1. Remove the 4 nuts and the rear light assembly.


3. REMOVE REAR LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


4. REMOVE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

  1. B146108E01
    Disengage the clamp.

  1. Disconnect the cable and connector.

  1. Remove the 2 bolts and luggage compartment door lock assembly.


5. REMOVE LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY

  1. B146109
    Disconnect the cable and connector.

  1. B146110
    Remove the 2 nuts and the luggage compartment door lock cylinder assembly.


6. REMOVE REAR SPOILER (w/ Rear Spoiler)

HINT:
When removing the rear spoiler, heat the vehicle body and rear spoiler using a heat light.

Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Spoiler
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and rear spoiler excessively.

  1. B160678
    Disconnect the connector.

  1. Remove the 2 nuts.

  1. Disengage the 2 clips and peel off the 2 No. 1 rear spoiler protectors, then remove the rear spoiler.

    B159270E01


7. REMOVE LUGGAGE DOOR OPENING SWITCH ASSEMBLY (w/ Smart Entry and Start System)
  1. Disconnect the connector.

  1. B142421
    Remove the 2 nuts and the luggage door opening switch assembly.


8. REMOVE BACK DOOR GARNISH RETAINER (w/ Smart Entry and Start System)

  1. without Parking Assist Monitor System:

    1. B151763
      Remove the 2 nuts.

    2. B151764
      Disengage the 2 claws and remove the back door garnish retainer.


9. REMOVE TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)

  1. E134847E01
    Disengage the camera connector clamp.

  1. Disconnect the television camera connector.

  1. Remove the 2 nuts.

  1. E134848E01
    Disengage the 2 claws to remove the television camera assembly as shown in the illustration.


10. REMOVE LUGGAGE COMPARTMENT OUTSIDE DOOR GARNISH SUB-ASSEMBLY (w/o Smart Entry and Start System)

  1. B149481E01
    Put protective tape around the luggage compartment door outside garnish sub-assembly.

  1. B149482
    Remove the 6 nuts.

  1. B159302E01
    Using a moulding remover, disengage the 4 clips and remove the luggage compartment door outside garnish sub-assembly.

    HINT:
    Disengage either lock on the clip to prevent the clip from breaking.


11. REMOVE LUGGAGE COMPARTMENT OUTSIDE DOOR GARNISH SUB-ASSEMBLY (w/ Smart Entry and Start System)

  1. B149481E01
    Put protective tape around the luggage compartment door outside garnish sub-assembly.

  1. B149484
    Remove the 2 nuts.

  1. B159302E01
    Using a moulding remover, disengage the 4 clips and remove the luggage compartment door outside garnish sub-assembly.

    HINT:
    Disengage either lock on the clip to prevent the clip from breaking.


12. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH
  1. Disconnect the connector.

  1. E134265E01
    Disengage the 2 claws and remove the license plate light assembly as shown in the illustration.


13. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.

← ON-VEHICLE INSPECTION (from Oct 2006)DISASSEMBLY (from Jun 2009) →