REMOVAL
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE REAR SEAT CUSHION ASSEMBLY |
 |
for Fixed Seat Type: (Click here)for Fold Down Seat Type: (Click here)
| 2.
REMOVE REAR SEAT HEADREST ASSEMBLY |
|
| 3.
REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest) |
|
| 4.
REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)
|
 |
- Remove the 3 rear seat belts from the 3 rear seat shoulder belt guides.
- Remove the 4 bolts and rear seatback assembly.
| 5.
REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
|
 |
- Remove the 2 bolts and separate type rear seatback assembly LH.
| 6.
REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
|
 |
- Remove the 2 bolts and separate type rear seatback assembly RH.
| 7.
REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
|
 |
- Remove the bolt and rear side seatback assembly LH.
| 8.
REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
|
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 9.
REMOVE REAR DOOR SCUFF PLATE LH
|
 |
- Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.
| 10.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
|
| 11.
REMOVE REAR DOOR SCUFF PLATE RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 12.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
|
| 13.
REMOVE NO. 1 SEAT BRACKET (for Fixed Seat Type)
|
 |
Remove the 2 nuts and the No. 1 seat bracket.
| 14.
DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
|
 |
- Remove the bolt and disconnect the floor end of the rear seat inner with center belt assembly LH.
| 15.
REMOVE ROOF SIDE INNER GARNISH LH
|
 |
- Disengage the 5 clips and 2 claws, and remove the roof side inner garnish LH.
| 16.
REMOVE ROOF SIDE INNER GARNISH RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 17.
DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
|
 |
- Remove the bolt and disconnect the floor end of the rear seat outer belt assembly LH.
| 18.
DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH
|
 |
- Remove the bolt and disconnect the floor end of the rear seat outer belt assembly RH.
| 19.
REMOVE REAR SEAT SHOULDER BELT COVER
|
 |
- Using a screwdriver, disengage the 4 claws and remove the rear seat shoulder belt cover.
- HINT:
- Tape the screwdriver tip before use.
- Use the same procedure for the RH side and LH side.
| 20.
REMOVE REAR SEAT SHOULDER BELT HOLE COVER
|
 |
- Using a screwdriver, disengage the 4 claws and remove the rear seat shoulder belt hole cover.
- HINT:
- Tape the screwdriver tip before use.
| 21.
REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
|
 |
- without Rear Spoiler:
Disconnect the connector.
Disengage the 4 clips and the 5 claws.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly, then remove the package tray trim panel assembly.
- with Rear Spoiler:
Disengage the 4 clips and the 5 claws.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly, then remove the package tray trim panel assembly.
| 22.
REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
|
 |
- Disengage the 2 clips and raise the front portion of the package tray trim panel assembly.
Pass the 3 rear seat belt floor anchors through the holes in the package tray trim panel assembly.
Remove the package tray trim panel assembly.
| 23.
REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
|
 |
Disconnect the connector.
- Disengage the 4 clips and 5 claws and remove the No. 2 package tray trim panel assembly.
| 24.
REMOVE CENTER STOP LIGHT SET (w/o Rear Sunshade) |
 |
- Disconnect the connector.
Remove the 2 screws and the center stop light set.
| 25.
REMOVE CENTER STOP LIGHT ASSEMBLY (w/ Rear Sunshade) |
 |
- Disengage the 4 claws and remove the center stop light assembly.