ON-VEHICLE INSPECTION
Inspection · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| CHECK IGNITION COIL ASSEMBLY AND PERFORM SPARK TEST |
- NOTICE:
- In this section, the terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).
Check for DTCs.
- NOTICE:
- If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.
Check that spark occurs.
Remove the No. 1 engine cover.
Disconnect the 4 ignition coil connectors and remove the 4 bolts and ignition coils.
Using a 16 mm (0.63 in.) spark plug wrench, remove the 4 spark plugs.

Disconnect the 4 fuel injector connectors.

Install the spark plug to each ignition coil, and connect the ignition coil connectors.
Ground the spark plug.

Check if a spark occurs at each spark plug while the engine is being cranked.
- NOTICE:
- Be sure to ground the spark plugs when checking.
- Replace the ignition coil if it receives an impact.
- Do not crank the engine for more than 2 seconds.
- Be sure to ground the spark plugs when checking.
Perform the spark test according to the flowchart below.
Check that the ignition coil connector is securely connected.
- Result:
Result
Proceed to
NG
Connect securely
OK
Go to next step
Perform the spark test on each ignition coil.
- Replace the ignition coil with a normal one.
- Perform the spark test again.
- Result:
Result
Proceed to
OK
Replace ignition coil
NG
Go to next step
- Replace the ignition coil with a normal one.
Check the power supply to the ignition coil.

- Turn the ignition switch to the ON position.
- Measure the voltage between the terminals of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
1 (+B) - 4 (GND)
9 to 14 V
- Result:
Result
Proceed to
NG
Check wire harness and connector
OK
Go to next step
- Turn the ignition switch to the ON position.
Measure the resistance of the camshaft position sensor.
- Standard resistance:
Temperature
Specified Condition
Cold
835 to 1,400 Ω
Hot
1,060 to 1,645 Ω
- Result:
Result
Proceed to
NG
Replace camshaft position sensor
OK
Go to next step
Measure the resistance of the crankshaft position sensor.
- Standard resistance:
Temperature
Specified Condition
Cold
985 to 1,600 Ω
Hot
1,265 to 1,890 Ω
- Result:
Result
Proceed to
NG
Replace crankshaft position sensor
OK
Go to next step
Check the IGT signal from the ECM (Click here).
- Result:
Result
Proceed to
NG
Check ECM
OK
Repair wiring between ignition coil and ECM
Using a 16 mm (0.63 in.) plug wrench, install the spark plug.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Install the 4 ignition coils with the 4 bolts and connect the 4 ignition coil connectors.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Connect the 4 fuel injector connectors.
Install the No. 1 engine cover.
| CHECK SPARK PLUG |
Check the electrode.

Using a megohmmeter, measure the insulation resistance.
- Standard insulation resistance:
- 10 MΩ or more
- HINT:
- If a megohmmeter is not available, perform the following simple inspection instead.
- If the result is 10 MΩ or less, clean the plug and measure the resistance again.
- If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:

Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is damage, replace the spark plug.- Recommended spark plug:
Manufacturer
Spark plug type
DENSO
SK20R11
NGK
IFR6A11
Check the spark plug electrode gap.

- Maximum electrode gap for used spark plug:
- 1.3 mm (0.051 in.)
- Electrode gap for new spark plug:
- 1.0 to 1.1 mm (0.039 to 0.043 in.)
Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.- Standard air pressure:
- 588 kPa (6 kgf*cm2, 85 psi)
- Standard duration:
- 20 seconds or less
- HINT:
- Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
