REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
|
| 2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
|
| 4.
SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY |
 |
- Secure the steering wheel with the seat belt in order to prevent rotation.
- HINT:
- This operation is useful to prevent damage to the spiral cable.
- Remove the bolt and slide the steering intermediate shaft assembly.
- NOTICE:
- Do not separate the steering intermediate shaft assembly from the power steering link assembly.
- Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
Separate the steering intermediate shaft assembly from the power steering link assembly.
| 5.
SEPARATE TIE ROD ASSEMBLY LH |
 |
Remove the cotter pin and the nut.
- Using SST, separate the tie rod assembly LH from the steering knuckle.
- SST
- 09628-00011
- NOTICE:
- Hang SST with a string, etc. to prevent it from falling.
- Do not damage the front disc brake dust cover.
- Do not damage the ball joint dust cover.
- Do not damage the steering knuckle.
| 6.
SEPARATE TIE ROD ASSEMBLY RH |
 |
- HINT:
- Perform the same procedure as for the LH side.
| 7.
REMOVE ENGINE ASSEMBLY WITH TRANSAXLE |
 |
- HINT:
- Refer to the instructions for removal of the engine assembly (Click here for 2AZ-FE, Click here for 2GR-FE).
| 8.
DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for LHD) |
 |
- Using SST, disconnect the pressure feed tube assembly (return tube side) from the power steering link assembly.
- SST
- 09023-12701
- Using SST, disconnect the pressure feed tube assembly (pressure feed tube side) from the power steering link assembly.
- SST
- 09023-12701
- Remove the bolt, nut, and separate the pressure feed tube clamp.
| 9.
DISCONNECT RETURN TUBE SUB-ASSEMBLY (for 2AZ-FE RHD) |
 |
- Slide the clip and disconnect the return tube sub-assembly.
| 10.
REMOVE RETURN TUBE ASSEMBLY (for 2AZ-FE RHD) |
 |
- Using SST, remove the return tube assembly from the power steering link assembly.
- SST
- 09023-12701
| 11.
DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for 2AZ-FE RHD) |
 |
- Using SST, disconnect the pressure feed tube assembly from the power steering link assembly.
- SST
- 09023-12701
- Remove the nut and separate the pressure feed tube clamp.
| 12.
DISCONNECT RETURN TUBE SUB-ASSEMBLY (for 2GR-FE RHD) |
 |
- Slide the clip and disconnect the return tube sub-assembly.
| 13.
REMOVE RETURN TUBE ASSEMBLY (for 2GR-FE RHD) |
 |
- Using SST, remove the return tube assembly from the power steering link assembly.
- SST
- 09023-12701
| 14.
DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for 2GR-FE RHD) |
 |
- Using SST, disconnect the pressure feed tube assembly from the power steering link assembly.
- SST
- 09023-12701
- Remove the nut and separate the pressure feed tube clamp.
| 15.
REMOVE POWER STEERING LINK ASSEMBLY |
 |
- Remove the 2 bolts, 2 nuts, and power steering link assembly.
- NOTICE:
- Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed.
| 16.
REMOVE POWER STEERING RACK HOUSING HEAT INSULATOR (for 2GR-FE LHD) |
 |
- Remove the power steering rack housing heat insulator from the power steering link assembly.
| 17.
REMOVE POWER STEERING RACK HOUSING HEAT INSULATOR (for 2GR-FE RHD) |
 |
- Remove the bolt and power steering rack housing heat insulator from the power steering link assembly.
| 18.
REMOVE TIE ROD ASSEMBLY LH |
 |
- Put matchmarks on the tie rod assembly LH and the steering rack end sub-assembly.
Loosen the lock nut, and remove the tie rod assembly LH and the lock nut.
| 19.
REMOVE TIE ROD ASSEMBLY RH |
 |
- HINT:
- Perform the same procedure as for the LH side.