Open in One Side of CAN Branch Line
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Communication Bus Check" screen, one side of the CAN branch wire may be open. (One side of the CAN-H [branch wire] / CAN-L [branch wire] of the ECU and/or sensor is open.)| Symptom |
Trouble Area |
| 2 or more ECUs and/or sensors do not appear on the intelligent tester "Communication Bus Check" screen. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- HINT:
- Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE |
Confirm the systems (ECUs and sensors), which use CAN communication, equipped on the vehicle. (Click here)
Using the intelligent tester, select and perform "Bus Check". (Click here) [*1]
Observe the screen for approximately 1 minute to check the ECUs and sensors that are not displayed on the screen and also those that repeatedly appear and disappear from the screen.
Disconnect the branch wire connectors, which are connected to the ECUs or sensors that are not displayed on the screen, from the CAN J/C.


CAN No. 1 J/C


CAN No. 1 J/C connectors ("A" side, with earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
CAN Main Bus Wire (E42)
White
B
W
Center Airbag Sensor Assembly (E45)
Black
B
W
*: with VSCCAN No. 1 J/C connectors ("B" side, without earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
A/C Amplifier (E47)
Gray
B
W
Combination Meter (E43)
White
B
W
Main Body ECU (E44)
Black
B
W
Yaw Rate Sensor (E46)*
Blue
B
W
CAN No. 4 J/C (REAR OF THE VEHICLE)


Terminals
Wiring Color
Connects to
A40-1 (CANH)
B
ECM (CANH)
A40-7 (CANL)
W
ECM (CANL)
A40-2 (CANH)
B
Skid Control ECU (CANH)
A40-8 (CANL)
W
Skid Control ECU (CANL)
CAN No. 4 J/C (FRONT OF THE VEHICLE)


Terminals
Wiring Color
Connects to
E41-2 (CANH)
B
DLC3 (CANH)
E41-8 (CANL)
W
DLC3 (CANL)
E41-4 (CANH)
B
CAN No. 1 J/C (CANH)
E41-10 (CANL)
W
CAN No. 1 J/C (CANL)
E41-3 (CANH)
B
Steering Angle Sensor (CANH)
E41-9 (CANL)
W
Steering Angle Sensor (CANL)
- HINT:
- Connecting locations of the connectors shown in the above tables are those of a vehicle whose connector locations have never been changed.
- If the connector locations differ from those shown in the above tables, identify each connector according to the color of the bus wires.
- Connecting locations of the connectors shown in the above tables are those of a vehicle whose connector locations have never been changed.
Check that the ECUs and sensors, which repeatedly appeared and disappeared from the "Bus Check" screen, are constantly displayed.
Perform the communication stop mode check for the ECUs and sensors which correspond to the disconnected branch wire connectors.
| NEXT | ||
| ||
