2006-2011 Camry Aurion · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL PARKING BRAKE PEDAL ASSEMBLY

  1. C132690
    Install the parking brake pedal assembly with the bolt and 2 nuts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Connect the parking brake switch connector.

  1. C133447
    Install the No. 1 parking brake cable assembly to the body with the bolt.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. C133438
    Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable assembly.


2. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

  1. C133468
    Engage the 3 claws and install the No. 1 air duct sub-assembly.


3. CONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY
  1. Connect the No. 4 parking brake cable assembly to the No. 1 parking brake cable assembly.

  1. C143746E01
    Using SST and a wrench, hold the lock nut of the No. 1 parking brake cable and tighten the turnbuckle of the No. 4 parking brake cable assembly.
    SST
    09023-00101  

    Torque:
    without SST:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    with SST:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque is effective when SST is parallel to a torque wrench.


4. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133884E01
    Install the center airbag sensor assembly with the 3 bolts.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  1. Connect the holder (with connectors).

  1. Check that the water-proof sheet is properly set.


5. INSTALL FLOOR SHIFT LEVER ASSEMBLY

  1. C224889
    Install the floor shift lever assembly with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


6. INSTALL FLOOR CARPET BRACKET LH

7. INSTALL FLOOR CARPET BRACKET RH

8. INSTALL YAW RATE AND ACCELERATION SENSOR

  1. C145964
    Install the yaw rate and acceleration sensor to the bracket with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C145963
    Install the yaw rate and acceleration sensor with the 2 bolts.

    NOTICE:
    1. Do not damage the yaw rate or acceleration sensor.
    2. Make sure that the yaw rate and acceleration sensor is installed securely.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the yaw rate and acceleration sensor connector.


9. INSTALL NO. 1 CONSOLE BOX DUCT

  1. C129716
    Install the No. 1 console box duct with the clip.


10. INSTALL CONSOLE BOX ASSEMBLY

  1. B158940
    Engage the 2 claws.

  1. B158939
    Install the 2 bolts <I>.

  1. B158937
    Install the 3 screws <H>.

  1. B158938
    Install the console box assembly with the 3 screws <H>.

  1. B158936E01
    Engage the clamp.


11. INSTALL CONSOLE BOX CARPET

  1. B158935
    Install the console box carpet.


12. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect the connector.

  1. B158962
    Engage the 10 claws and install the upper console panel sub-assembly.


13. INSTALL UPPER CONSOLE PANEL FRONT GARNISH

  1. B158963
    Connect each connector.

  1. Engage the 6 claws and install the upper console panel front garnish.


14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B158971
    Install the shift lever knob sub-assembly.


15. INSTALL COMBINATION METER ASSEMBLY

  1. B158920
    Connect each connector.

  1. Install the combination meter assembly with the 4 screws <B>, <C> or <H>.


16. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B158919E01
    Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel sub-assembly with the 2 clips.


17. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector.

  1. B158916
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B158917
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)
  1. Connect the connector.

  1. B158918
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


20. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158922E01
    Engage the 3 claws and 3 clips.

  1. Install the screw <F> or <N>.

  1. Install the 3 screws <F>.

  1. Install the lower instrument panel sub-assembly with the bolt <D>.


21. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B158913E01
    Install the air hose and connect each connector.

  1. Engage the claw and the 4 clips.

  1. Engage the 2 claws and the DLC3.

  1. Install the lower No. 1 instrument panel finish panel with the screw <F> and bolt <D>.


22. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B158969E01
    Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover sub-assembly.


23. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


24. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


25. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


26. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

28. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).


29. INSPECT PARKING BRAKE PEDAL TRAVEL
  1. Fully depress the parking brake pedal and release it to engage the parking brake.

  1. Depress the pedal to the floor again, and release it to disengage the parking brake.

  1. C107204
    Slowly depress the parking brake pedal to the floor, and count the number of clicks.

    Parking brake pedal travel:
    7 to 10 notches at 300 N (31 kgf, 67 lbf)


30. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Depress the parking brake pedal. Hold the No. 1 wire adjusting nut using a wrench and loosen the lock nut.

  1. Release the parking brake pedal.

  1. C133443E01
    Turn the No. 1 wire adjusting nut until the parking brake pedal travel meets the above specification.

  1. Hold the No. 1 wire adjusting nut using a wrench or an equivalent tool and tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Count the number of clicks after depressing and releasing the parking brake pedal 3 or 4 times.

  1. Check whether the parking brake drags.

  1. When operating the parking brake pedal, check that the parking brake indicator light comes on.

← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (Jun 2006 – Sep 2006) →