2006-2011 Camry Aurion · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


2. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


6. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


7. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133988E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


8. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B133992E01
    Remove the bolt <A>.

  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.


9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B226062
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


10. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B226063
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


11. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B226064
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


12. REMOVE POSITION INDICATOR HOUSING ASSEMBLY

  1. B226065
    Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.


13. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY

  1. B226097
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


14. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B133997E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.


15. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.


16. REMOVE CONSOLE BOX CARPET

  1. B134004
    Remove the console box carpet.


17. REMOVE CONSOLE BOX ASSEMBLY

  1. B134002E01
    Remove the 2 screws <F>.

  1. B149935E03
    Disengage the clamp.

  1. Remove the 2 bolts <G> and the console box assembly.


18. REMOVE NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.


19. REMOVE NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.


20. REMOVE NO. 1 CONSOLE BOX DUCT

  1. C129716
    Remove the clip and No. 1 console box duct.


21. REMOVE FLOOR CARPET BRACKET LH

  1. E129146E01
    Release the clamp.

  1. Turn back the floor carpet.

  1. E128512
    Remove the 3 clips.

  1. Remove the floor carpet bracket LH.


22. REMOVE FLOOR CARPET BRACKET RH

  1. E129147E01
    Release the clamp.

  1. Turn back the floor carpet.

  1. E128513
    Remove the 3 clips.

  1. Remove the floor carpet bracket RH.


23. REMOVE FLOOR SHIFT LEVER ASSEMBLY

  1. C132691
    Remove the 4 bolts and the floor shift lever assembly.


24. REMOVE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn back the carpet.

  1. C133884
    Disconnect the holder (with connectors).

  1. Remove the 3 bolts and center airbag sensor assembly.


25. DISCONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY

  1. C132693E01
    Using 2 wrenches, hold the lock nut and loosen the turnbuckle.

  1. Disconnect the No. 4 parking brake cable assembly from the No. 1 parking brake cable assembly.


26. REMOVE PARKING BRAKE PEDAL ASSEMBLY

  1. C132692
    Using needle-nose pliers, remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the bolt, the nut, and the No. 1 parking brake cable clamp.

    C132694

  1. Separate the No. 1 parking brake cable assembly from the body.

  1. C143766
    Disconnect the parking brake switch connector.

  1. Remove the bolt, 2 nuts, and the parking brake pedal assembly with the No. 1 parking brake cable assembly from the body.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (Oct 2006 – May 2009) →