2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL ECM

  1. A135713
    Install the ECM bracket with the 4 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. A135712
    Connect the 2 connectors.

  1. A135711
    Install the ECM with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


2. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

  1. A136272
    Install the cowl top panel outer sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }


3. INSTALL WINDSHIELD WIPER MOTOR AND LINK

  1. E135590E01
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.

  1. E135589
    Connect the connector.


4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E135588
    Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Engage the claw and install the front fender to cowl side seal RH.


6. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Engage the claw and install the front fender to cowl side seal LH.


7. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128820E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)


8. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128821E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← REMOVAL (from Jun 2009)INSTALLATION (from Jun 2009) →