REGISTRATION
Other · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
- HINT:
- Register the recognition code when replacing the door control transmitter or the door control receiver.
- Add mode is used to retain the already registered codes while registering a new recognition code. This mode is used when adding a transmitter. If the number of registered codes exceeds 4, the previously registered code will be correspondingly erased in order, starting from the code registered first.
- Rewrite mode is used to erase all the previously registered codes and register only new recognition codes. This mode is used when exchanging the transmitter or the door control receiver for new one.
- Confirmation mode is used to confirm how many recognition codes have already been registered before an additional registration of a recognition code.
- Prohibition mode is used to erase all the registered codes and cancel the wireless door lock function. Use this mode when the transmitter is lost.
- All the following registration procedures must be performed in order continuously.
- Register the recognition code when replacing the door control transmitter or the door control receiver.
| 1. REGISTRATION OF RECOGNITION CODE (MANUAL OPERATION) |
The vehicle should be in the following conditions.
No key is inserted in the ignition key cylinder.
Only driver's door is opened.
Perform the following operations to select the desired mode.
Insert and remove the key from the ignition switch twice within 5 seconds. (End in removed)
After the above operations, close and open the driver door twice. (End in open)
Then insert the key into the ignition key cylinder and remove it.- HINT:
- Complete these procedures within 40 seconds.
After the above operations, close and open the driver door twice. (End in open)
Then insert the key into the ignition key cylinder and close the door.- HINT:
- Complete these procedures within 40 seconds.
Turn the ignition switch from LOCK to ON and back to LOCK at approximately 1 second interval 1 to 5 times to select a mode (see the illustration). Then remove the key from the ignition key cylinder.


- HINT:
- Complete these procedures within 40 seconds.
- NOTICE:
- If the number of the ON-LOCK operations of the ignition switch is 0, 4 or 6 or more, there will be no response to inform which mode has been selected.
After selecting a mode, the main body ECU automatically performs the power door LOCK- UNLOCK operation within 5 seconds to inform the selected mode (see the illustration).


- HINT:
- In the confirmation mode, the LOCK- UNLOCK operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, the LOCK-UNLOCK operation will occur 2 times.
- In confirmation mode and prohibition mode, once a LOCK-UNLOCK operation response has occurred, the registration procedure will end.
- In the confirmation mode, the LOCK- UNLOCK operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, the LOCK-UNLOCK operation will occur 2 times.
Register the new recognition codes (Add mode or Rewrite mode):
Within 45 seconds after the add mode or the rewrite mode has been selected, press the LOCK and UNLOCK switches on the transmitter switch simultaneously for 1.0 to 1.5 seconds.
And then press either of the switches for more than 1.0 second (Procedure "A").Within 5 seconds after the transmitter switch has been released, the LOCK-UNLOCK operation will be automatically performed once if the registration of the recognition code of the transmitter is completed correctly.
In case the LOCK-UNLOCK operation is performed twice, the registration of recognition code has failed. Perform the registration procedure from the beginning once again (Procedure "B").

If multiple transmitters need to be registered, repeat procedure "A" and "B" within 45 seconds after the previous registration.
- HINT:
- 4 recognition codes can be registered at once.
- If even one of the following conditions is satisfied, the registration mode will end.
- 40 seconds have elapsed after a recognition code has been registered.
- Any of the doors are opened.
- The key is inserted into the ignition key cylinder.
- 4 recognition codes are registered.
- 4 recognition codes can be registered at once.
| 2. REGISTRATION OF RECOGNITION CODE (USING INTELLIGENT TESTER) |
Turn the ignition switch to the ON position.
Select the add or rewrite mode according to the intelligent tester display.
The number of registered codes is indicated.
Registration of the door control transmitter.
If the add mode or rewrite mode has been selected, press the LOCK and UNLOCK switches on the transmitter simultaneously.
Within 3 seconds of releasing the LOCK and UNLOCK switches, press either of the switches on the door control transmitter.
- NOTICE:
- Do not press the LOCK and UNLOCK switches simultaneously for more than 1.5 seconds.
- Do the operation within 1 meter of the driver's seat to register the transmitter.
- Do not push other transmitter switches during the transmitter registration process.
- Do not press the LOCK and UNLOCK switches simultaneously for more than 1.5 seconds.
The main body ECU automatically performs the power door LOCK-UNLOCK operation once and sounds the wireless door lock buzzer twice, in order to indicate whether registration has been completed correctly or not.
If registration is continued, the next recognition code must be registered in the door control transmitter within 30 seconds.
- HINT:
- Up to 4 recognition codes can be registered.
Completing the registration mode.
The registration mode will cease when any of the following occurs:
- 30 seconds or more have elapsed after a code is registered.
- The intelligent tester is used to complete.
- The intelligent tester is disconnected.
- The ignition switch is turned off.
- 30 seconds or more have elapsed after a code is registered.
Perform the following after registration is completed.
Perform the wireless door lock control operation check (Click here).
- HINT:
- If the wireless door lock control does not operate, perform the registration procedure again.
