REASSEMBLY
Removal / installation · Vehicles built Jun 2006 – May 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
| 1.
INSTALL REAR SEPARATE TYPE SEATBACK COVER LH |
 |
- Using hog ring pliers, install the rear separate type seatback cover with 9 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 2.
INSTALL REAR SEPARATE TYPE SEATBACK COVER RH (w/o Center Armrest) |
 |
- Using hog ring pliers, install the rear separate type seatback cover to the seatback pad with 11 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 3.
INSTALL REAR SEPARATE TYPE SEATBACK COVER RH (w/ Center Armrest) |
 |
- Using hog ring pliers, install the rear separate type seatback cover to the seatback pad with 9 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Using hog ring pliers, install the rear separate type seatback cover to the seatback pad with 7 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 4.
INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH |
 |
- Install the rear seatback frame sub-assembly LH.
| 5.
INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH |
 |
- Install the rear seatback frame sub-assembly RH.
| 6.
INSTALL REAR SEAT HEADREST SUPPORT (for LH Side) |
 |
- Engage the 2 claws to install each rear seat headrest supports.
- Using hog ring pliers, install the rear separate type seatback cover to the seatback frame with 6 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Engage the 2 hooks.
| 7.
INSTALL REAR SEATBACK LOCK BEZEL UPPER (for LH Side) |
 |
- Engage the 4 claws to install the rear seatback lock bezel upper.
| 8.
INSTALL REAR SEAT HEADREST SUPPORT (for RH Side) |
 |
- Engage the 2 claws to install each rear seat headrest supports.
- Using hog ring pliers, install the rear separate type seatback cover to the seatback frame with 7 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Engage the 2 hooks.
| 9.
INSTALL REAR SEATBACK LOCK BEZEL UPPER (for RH Side) |
 |
- Engage the 4 claws to install the rear seatback lock bezel upper.
| 10.
INSTALL REAR SEAT SHOULDER BELT GUIDE RH |
 |
- Install the rear seat shoulder belt guide RH with the 2 screws.
| 11.
INSTALL REAR SEAT SHOULDER BELT GUIDE LH |
 |
- Seatback:
Install the rear seat shoulder belt guide LH with the 2 screws.
- Side Seatback:
Install the rear seat shoulder belt guide LH with the 2 screws.
| 12.
REMOVE REAR SEAT BELT HOOK |
 |
- Install the rear seat belt hook.
- HINT:
- Use the same procedures for the RH side and LH side.
| 13.
INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY (w/ Center Armrest) |
 |
- Engage the 4 claws to install the rear seat center armrest cup holder.
| 14.
INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Armrest) |
 |
- Install the bush.
- Install the rear center seat armrest assembly as shown in the illustration.
| 15.
INSTALL REAR SEATBACK HINGE COVER (w/ Center Armrest) |
 |
- Install the rear seatback hinge cover.
- Install the bolt and bush.
| 16.
INSTALL NO. 1 SEAT ARMREST CAP (w/ Center Armrest) |
 |
- Install the No. 1 seat armrest cap.
| 17.
INSTALL REAR BENCH TYPE SEAT CUSHION COVER |
 |
Using hog ring pliers, install 16 new hog rings.


- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install the rear bench type seat cushion cover to the seat cushion pad with 36 new hog rings.


- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.