INSTALLATION
Removal / installation · Vehicles built Jun 2006 – Sep 2006
| 1. INSTALL NO. 3 INSTRUMENT PANEL STAY |
Engage the 5 claws and install the 5 new No. 3 instrument panel stays.


| 2. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Engage the 5 claws.
- NOTICE:
- Do not allow the wire harness to get caught in the claws.
Install the 2 bolts <H> and 2 nuts <I>.


Engage each clamp.
Install the bolt <J>.
- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
Install the 2 passenger airbag bolts <C>.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Connect each connector and install the instrument panel safety pad assembly.


| 3. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY |
Connect the connector (yellow colored one).

| 4. INSTALL NO. 1 DEFROSTER NOZZLE GARNISH |
Connect each connector.

Engage the 4 guides.
Engage the 8 clips and install the No. 1 defroster nozzle garnish.
| 5. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH (for 6 Speakers) |
Connect the connector.
Install the front No. 2 speaker assembly with the 2 bolts.

| 6. INSTALL INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY |
Engage the 2 guides.

Engage the 6 claws and the 2 clips to install the instrument panel No. 1 speaker panel sub-assembly.
| 7. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY |
Engage the 4 clips and install the instrument panel No. 1 register assembly.

| 8. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag) |
Install a new clip <A> on the front pillar garnish LH.

Engage the 2 claws and 2 clips, then install the front pillar garnish LH.
| 9. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag) |
Remove the protective cover.

Install a new clip <A> on the front pillar garnish LH.

Engage the 2 claws and 2 clips, then install the front pillar garnish LH.
| 10. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH (for 6 Speakers) |
- HINT:
- Use the same procedures for the RH side and the LH side (Click here).
| 11. INSTALL INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY |
Engage the 2 guides.

Engage the 6 claws and the 2 clips to install the instrument panel No. 2 speaker panel sub-assembly.
| 12. INSTALL INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY |
Engage the 4 clips and install the instrument panel No. 3 register assembly.

| 13. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag) |
Install a new clip <A> on the front pillar garnish RH.

Engage the 2 claws and 2 clips, then install the front pillar garnish RH.
| 14. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag) |
Remove the protective cover.

Install a new clip <A> on the front pillar garnish RH.

Engage the 2 claws and 2 clips, then install the front pillar garnish RH.
| 15. INSTALL NO. 1 CONSOLE BOX INSERT FRONT |
Engage the clip.

Install the No. 1 console box insert front with the 3 screws <F>.
| 16. INSTALL NO. 2 CONSOLE BOX INSERT FRONT |
Engage the clip.

Install the No. 2 console box insert front with the 3 screws <F>.
| 17. INSTALL CONSOLE BOX ASSEMBLY |
Install the 2 screws <F>.

Install the console box assembly with the 2 bolts <G>.

Engage the clamp.
| 18. INSTALL CONSOLE BOX CARPET |
Install the console box carpet.

| 19. INSTALL CONSOLE BOX POCKET |
Install the console box pocket.
| 20. INSTALL RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player) |
Connect each connector.

Engage the 6 clips.
Install the radio and cassette tape with heater control panel assembly with the 4 bolts.
| 21. INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player) |
Connect each connector.

Engage the 4 clips.
Install the radio receiver with heater control panel assembly with the 4 bolts.
| 22. INSTALL NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System) |
Connect each connector.
Engage the 4 clips.

Install the navigation receiver with heater control panel assembly with the 4 bolts.
| 23. INSTALL INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY |
Connect the connector.
Engage the 7 clips and install the instrument panel No. 2 register assembly.

| 24. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
Connect each connector.
Engage the 2 claws and 2 clips.

Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.
| 25. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD) |
Connect the connector.

Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 26. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD) |
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.

| 27. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle) |
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.

| 28. INSTALL POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD) |
Engage the 6 claws and the 3 clips to install the position indicator housing assembly.

| 29. INSTALL POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD) |
Engage the 2 claws and the 5 clips to install the position indicator housing assembly as shown in the illustration.

| 30. INSTALL UPPER CONSOLE PANEL (for Manual Transaxle) |
Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.

| 31. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.

| 32. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.

| 33. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD) |
Install the shift lever knob sub-assembly.

| 34. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD) |
Install the shift lever knob sub-assembly.

| 35. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
Install the shift lever knob sub-assembly.

| 36. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Engage the 3 claws and 3 clips.

Install the 4 screws <B>.
Install the lower instrument panel sub-assembly with the bolt <A>.
| 37. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
Engage the 4 claws and 2 guides, and install the instrument panel No. 2 under cover sub-assembly.

| 38. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 39. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 40. INSTALL COMBINATION METER ASSEMBLY |
Connect each connector.

Install the combination meter assembly with the 4 screws <E>.
| 41. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
Engage the guide and the 4 claws.

Install the instrument cluster finish panel sub-assembly with the 2 clips.
| 42. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL |
Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.

| 43. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD) |
Connect each connector.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.

| 44. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD) |
Connect each connector.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.

| 45. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 46. ADJUST SPIRAL CABLE SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

- NOTICE:
- Do not turn the spiral cable by the airbag wire harness.
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

- NOTICE:
- Do not turn the spiral cable by the airbag wire harness.
- HINT:
- The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
| 47. INSTALL STEERING COLUMN COVER |
Engage the claw and install the upper steering column cover.

Engage the 2 claws and install the lower steering column cover.
Install the steering column cover with the 2 screws <D>.
- Torque:
- 2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
| 48. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Install the air hose and connect the connector.

Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.
| 49. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
Engage the 2 clips.

Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 50. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

| 51. INSTALL STEERING WHEEL ASSEMBLY |
Align the matchmarks on the steering wheel assembly and steering main shaft.

Install the steering wheel assembly set nut.
- Torque:
- 50 N*m{ 510 kgf*cm , 37 ft.*lbf }
Connect the connectors to the spiral cable sub-assembly.
| 52. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Support the steering pad with one hand.

Connect the 2 airbag connectors to the steering pad.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

- Torque:
- 8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
| 53. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
Engage the claw and install the No. 3 lower steering wheel cover.


| 54. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
Engage the claw and install the No. 2 lower steering wheel cover.


| 55. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 56. INSPECT STEERING PAD |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

- Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
- Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
Make sure that the horn sounds.
- HINT:
- If the horn does not sound, inspect the horn system (Click here).
| 57. INSPECT SRS WARNING LIGHT |
